Kernel Netconsole freezes boot

[godofdream]

Device: Goflexnet, newest uBoot and Rescue V2 from Jeff Doozans site
I'm using Debian (not important as the issue is kernel related)
with an self build 3.7.4 Kernel including Archlinuxarm patches.
It's working more or less, as bfq has some problems.

I want to test my newer 3.8.3 Kernel with the fix for bfq, but it crashes, so i set up netconsole.
With netconsole enabled my current 3.7.4 kernel freezes after this output.
I can't test 3.8.3 until netconsole is working properly.
Any Hints?

$this->bbcode_second_pass_code('', '
root@m-virtual-machine:~# nc -lu 6666

U-Boot 2011.12 (Apr 18 2012 - 23:08:20)
Seagate GoFlexNet
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1751
UBI: number of bad PEBs: 1
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1730
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..

Reset IDE: Bus 0: OK Bus 1: OK
Device 0: Model: SAMSUNG HD103UJ Firm: 1AA01113 Ser#: S13PJ9AQB16100
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953868.6 MB = 931.5 GB (1953523055 x 512)
Device 1: Model: ST3000DM001-1CH166 Firm: CC44 Ser#: W1F1K9B4
Type: Hard Disk
Supports 48-bit addressing
Capacity: 764436.4 MB = 746.5 GB (1565565872 x 512)
Loading file "/boot/uImage" from ide device 0:1 (hda1)
2615040 bytes read
Loading file "/boot/uInitrd" from ide device 0:1 (hda1)
4766800 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-3.7.4-1.3
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2614976 Bytes = 2.5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4766736 Bytes = 4.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.7.4-kirkwood (root@router) (gcc version 4.6.3 (Debian 4.6.3-14) ) #4 PREEMPT Fri Feb 22 22:19:53 CET 2013
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Seagate GoFlex Net
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 rootfstype=ext4 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) loglevel=7 netconsole=6666@192.168.178.100/eth0,6666@192.168.178.18/00:0c:29:f9:9d:87
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 115140k/115140k available, 15932k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc04b4064 (4785 kB)
[ 0.000000] .init : 0xc04b5000 - 0xc04db49c ( 154 kB)
[ 0.000000] .data : 0xc04dc000 - 0xc0522c90 ( 284 kB)
[ 0.000000] .bss : 0xc0522cb4 - 0xc09de540 (4847 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3679 kB
[ 0.000000] per task-struct memory footprint: 1152 bytes
[ 19.817266] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 19.898538] pid_max: default: 32768 minimum: 301
[ 19.900099] Mount-cache hash table entries: 512
[ 19.905706] Initializing cgroup subsys cpuacct
[ 19.905728] Initializing cgroup subsys devices
[ 19.905769] Initializing cgroup subsys freezer
[ 19.905811] Initializing cgroup subsys net_cls
[ 19.905848] Initializing cgroup subsys blkio
[ 19.905862] Initializing cgroup subsys perf_event
[ 19.905913] Initializing cgroup subsys bfqio
[ 19.906476] CPU: Testing write buffer coherency: ok
[ 19.907817] Setting up static identity map for 0x3540c8 - 0x354104
[ 19.914704] devtmpfs: initialized
[ 19.938048] NET: Registered protocol family 16
[ 19.939725] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 19.945509] Kirkwood: MV88F6281-A1, TCLK=200000000.
[ 19.945531] Feroceon L2: Enabling L2
[ 19.945571] Feroceon L2: Cache support initialised.
[ 19.984390] bio: create slab <bio-0> at 0
[ 19.987172] vgaarb: loaded
[ 19.991321] SCSI subsystem initialized
[ 19.994140] usbcore: registered new interface driver usbfs
[ 19.994608] usbcore: registered new interface driver hub
[ 19.995160] usbcore: registered new device driver usb
[ 20.000422] Switching to clocksource orion_clocksource
[ 20.127001] FS-Cache: Loaded
[ 20.191195] NET: Registered protocol family 2
[ 20.194160] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 20.194417] TCP bind hash table entries: 4096 (order: 5, 147456 bytes)
[ 20.195106] TCP: Hash tables configured (established 4096 bind 4096)
[ 20.195378] TCP: reno registered
[ 20.195404] UDP hash table entries: 256 (order: 2, 20480 bytes)
[ 20.195513] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[ 20.196891] NET: Registered protocol family 1
[ 20.198748] Trying to unpack rootfs image as initramfs...
[ 20.701776] Freeing initrd memory: 4652K
[ 20.705570] audit: initializing netlink socket (disabled)
[ 20.705853] type=2000 audit(0.890:1): initialized
[ 20.865735] VFS: Disk quotas dquot_6.5.2
[ 20.866748] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 20.882141] msgmni has been set to 233
[ 20.886788] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 20.886845] io scheduler noop registered
[ 20.886856] io scheduler deadline registered
[ 20.888684] io scheduler cfq registered
[ 20.890863] io scheduler bfq registered (default)
[ 20.891456] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[ 20.891719] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[ 20.931524] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 20.971527] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 21.011524] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[ 21.051524] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[ 21.078578] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 21.103154] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 21.607710] console [ttyS0] enabled
[ 21.657352] brd: module loaded
[ 21.683778] loop: module loaded
[ 21.692661] ONFI param page 0 valid
[ 21.696170] ONFI flash detected
[ 21.699333] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD), page size: 2048, OOB size: 64
[ 21.709837] Scanning device for bad blocks
[ 21.826768] Bad eraseblock 1036 at 0x000008180000
[ 21.941542] 4 cmdlinepart partitions found on MTD device orion_nand
[ 21.947839] Creating 4 MTD partitions on "orion_nand":
[ 21.953079] 0x000000000000-0x000000100000 : "u-boot"
[ 21.960636] 0x000000100000-0x000000500000 : "uImage"
[ 21.967597] 0x000000500000-0x000002500000 : "rootfs"
[ 21.974894] 0x000002500000-0x000010000000 : "data"
[ 21.984586] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 21.992257] libphy: mv643xx_eth smi: probed
[ 22.016740] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 02:50:43:67:b3:61
[ 22.025958] pch_gbe: EG20T PCH Gigabit Ethernet Driver - version 1.01
[ 22.033034] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 22.039881] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 22.045563] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 22.080615] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 22.100494] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 22.111273] hub 1-0:1.0: USB hub found
[ 22.115235] hub 1-0:1.0: 1 port detected
[ 22.122556] Initializing USB Mass Storage driver...
[ 22.127985] usbcore: registered new interface driver usb-storage
[ 22.134050] USB Mass Storage support registered.
[ 22.148527] gre: GRE over IPv4 demultiplexor driver
[ 22.153754] TCP: cubic registered
[ 22.157089] NET: Registered protocol family 17
[ 22.161968] lib80211: common routines for IEEE802.11 drivers
[ 22.168067] Key type dns_resolver registered
[ 22.177686] netpoll: netconsole: local port 6666
[ 22.182399] netpoll: netconsole: local IP 192.168.178.100
[ 22.187821] netpoll: netconsole: interface 'eth0'
[ 22.192571] netpoll: netconsole: remote port 6666
[ 22.197300] netpoll: netconsole: remote IP 192.168.178.18
[ 22.202746] netpoll: netconsole: remote ethernet address 00:0c:29:f9:9d:87
[ 22.209660] netpoll: netconsole: device eth0 not up yet, forcing it
[ 24.988903] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 25.015148] console [netcon0] enabled
[ 25.018930] netconsole: network logging started
[ 25.026143] Freeing init memory: 152K
[ 25.185624] udevd[47]: starting version 175
[ 25.653017] sata_mv sata_mv.0: cannot get optional clkdev
[ 25.658852] sata_mv sata_mv.0: slots 32 ports 2
[ 25.931038] scsi0 : sata_mv
[ 26.055022] scsi1 : sata_mv
[ 26.060145] ata1: SATA max UDMA/133 irq 21
[ 26.210975] ata2: SATA max UDMA/133 irq 21
[ 26.720701] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 26.748955] ata1.00: HPA detected: current 1953523055, native 1953525168
[ 26.779219] ata1.00: ATA-7: SAMSUNG HD103UJ, 1AA01113, max UDMA7
[ 26.808521] ata1.00: 1953523055 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 26.861252] ata1.00: configured for UDMA/133
[ 26.882622] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD103UJ 1AA0 PQ: 0 ANSI: 5
[ 26.940280] sd 0:0:0:0: [sda] 1953523055 512-byte logical blocks: (1.00 TB/931 GiB)
[ 26.964638] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 26.985156] sd 0:0:0:0: [sda] Write Protect is off
[ 26.994623] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 27.033181] sda: sda1 sda2 sda3 sda4
[ 27.049117] sd 0:0:0:0: [sda] Attached SCSI disk
[ 27.500511] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 27.507989] ata2.15: Port Multiplier 1.1, 0x1095:0x3726 r23, 6 ports, feat 0x1/0x9
[ 27.565026] ata2.00: hard resetting link
[ 28.070849] ata2.01: hard resetting link
[ 28.580819] ata2.02: hard resetting link
[ 29.090836] ata2.03: hard resetting link
[ 29.600821] ata2.04: hard resetting link
[ 30.110832] ata2.05: hard resetting link
[ 30.500548] ata2.00: ATA-8: ST3000DM001-1CH166, CC44, max UDMA/133
[ 30.506875] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.610555] ata2.00: configured for UDMA/133
[ 30.650538] ata2.01: ATA-8: ST3000DM001-1CH166, CC43, max UDMA/133
[ 30.656862] ata2.01: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.760551] ata2.01: configured for UDMA/133
[ 30.800538] ata2.02: ATA-8: ST2000DL003-9VT166, CC3C, max UDMA/133
[ 30.806862] ata2.02: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.910550] ata2.02: configured for UDMA/133
[ 30.950538] ata2.03: ATA-8: ST3000DM001-1CH166, CC43, max UDMA/133
[ 30.956864] ata2.03: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 31.060553] ata2.03: configured for UDMA/133
[ 31.100539] ata2.04: ATA-8: ST3000DM001-1CH166, CC44, max UDMA/133
[ 31.106871] ata2.04: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 31.210549] ata2.04: configured for UDMA/133
[ 31.215178] ata2: EH complete
[ 31.231791] scsi 1:0:0:0: Direct-Access ATA ST3000DM001-1CH1 CC44 PQ: 0 ANSI: 5
[ 31.244678] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 31.255240] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 31.260749] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 31.269222] scsi 1:1:0:0: Direct-Access ATA ST3000DM001-1CH1 CC43 PQ: 0 ANSI: 5
[ 31.279066] sd 1:0:0:0: [sdb] Write Protect is off
[ 31.284830] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 31.298524] sd 1:1:0:0: [sdc] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 31.309064] sd 1:1:0:0: Attached scsi generic sg2 type 0
[ 31.314569] sd 1:1:0:0: [sdc] 4096-byte physical blocks
[ 31.331464] scsi 1:2:0:0: Direct-Access ATA ST2000DL003-9VT1 CC3C PQ: 0 ANSI: 5
[ 31.342963] sd 1:1:0:0: [sdc] Write Protect is off
[ 31.348720] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 31.363940] sd 1:2:0:0: [sdd] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 31.374800] sd 1:2:0:0: Attached scsi generic sg3 type 0
[ 31.380633] sd 1:2:0:0: [sdd] 4096-byte physical blocks
[ 31.392910] sdb: sdb1
[ 31.403827] scsi 1:3:0:0: Direct-Access ATA ST3000DM001-1CH1 CC43 PQ: 0 ANSI: 5
[ 31.417221] sd 1:2:0:0: [sdd] Write Protect is off
[ 31.425677] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 31.431338] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 31.447370] sd 1:3:0:0: [sde] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 31.457923] sd 1:3:0:0: Attached scsi generic sg4 type 0
[ 31.468298] sd 1:3:0:0: [sde] 4096-byte physical blocks
[ 31.476979] sdc: sdc1
[ 31.487393] scsi 1:4:0:0: Direct-Access ATA ST3000DM001-1CH1 CC44 PQ: 0 ANSI: 5
[ 31.502945] sd 1:3:0:0: [sde] Write Protect is off
[ 31.509911] sd 1:1:0:0: [sdc] Attached SCSI disk
[ 31.515148] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 31.524609] sdd: sdd1
[ 31.536826] sd 1:4:0:0: [sdf] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 31.549725] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 31.554692] sd 1:4:0:0: Attached scsi generic sg5 type 0
[ 31.560498] sd 1:4:0:0: [sdf] 4096-byte physical blocks
[ 31.578308] sd 1:4:0:0: [sdf] Write Protect is off
[ 31.584106] sd 1:4:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 31.646658] sde: sde1
[ 31.656664] sd 1:3:0:0: [sde] Attached SCSI disk
[ 31.664536] sdf: sdf1
[ 31.674782] sd 1:4:0:0: [sdf] Attached SCSI disk
[ 43.901793] EXT4-fs (sda4): INFO: recovery required on readonly filesystem
[ 43.908841] EXT4-fs (sda4): write access will be enabled during recovery
[ 44.149332] EXT4-fs (sda4): recovery complete
[ 44.191297] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
[ 46.832257] udevd[313]: starting version 175
[ 53.891778] md: md0 stopped.
[ 53.942642] unwind: Index not found bf024878
')
$this->bbcode_second_pass_code('', 'root@router:~# fw_printenv
ethact=egiga0
baudrate=115200
mainlineLinux=yes
console=ttyS0,115200
led_init=green blinking
led_exit=green off
led_error=orange blinking
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
mtdids=nand0=orion_nand
partition=nand0,2
stdin=serial
stdout=serial
stderr=serial
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_list=1 2 3 4
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_device=0:1
usb_rootdelay=10
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
sata_device=0:1
sata_rootdelay=10
set_bootargs_rescue=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts
bootcmd_rescue=run set_bootargs_rescue; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000
bootcmd_pogo=run bootcmd_rescue
rescue_installed=1
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run sata_bootcmd; run rescue_bootcmd; run pogo_bootcmd; reset
bootdelay=5
if_netconsole=ping $serverip
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
preboot=run if_netconsole start_netconsole
usb_root=LABEL=rootfs
ethaddr=02:50:43:67:b3:61
arcNumber=3089
usb_init=run usb_scan; setenv usb_root LABEL=rootfs
usb_bootcmd=run usb_init; setenv usb_root LABEL=rootfs; run usb_set_bootargs; run usb_boot
sata_bootcmd=run sata_set_bootargs; run sata_boot
ipaddr=192.168.178.100
serverip=192.168.178.18
sata_root=LABEL=rootfs
sata_boot=ide reset; mw 0x800000 0 1; ext2load ide 0:1 0x800000 /boot/uImage; if ext2load ide 0:1 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
sata_rootfstype=ext4
usb_rootfstype=ext4
sata_set_bootargs=setenv bootargs console=$console root=$sata_root rootdelay=$sata_rootdelay rootfstype=$sata_rootfstype $mtdparts $usb_custom_params
usb_custom_params=loglevel=7 netconsole=6666@192.168.178.100/eth0,6666@192.168.178.18/00:0c:29:f9:9d:87
')

[moonman]

It seems to be working properly. Maybe there's nothing more to output so it stops?

[godofdream]

No, normally it starts up my software raid, and then the startscript activates some gpio-leds
maybe the cryptodev creates some problems, as it needs to be recompiled.
I will try tomorrow with disabled cryptodev.

normal start dmesg output:
$this->bbcode_second_pass_code('', '
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.7.4-kirkwood (root@router) (gcc version 4.6.3 (Debian 4.6.3-14) ) #4 PREEMPT Fri Feb 22 22:19:53 CET 2013
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Seagate GoFlex Net
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat c051f67c, node_mem_map c09df000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32512 pages, LIFO batch:7
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 rootfstype=ext4 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 115140k/115140k available, 15932k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc04b4064 (4785 kB)
[ 0.000000] .init : 0xc04b5000 - 0xc04db49c ( 154 kB)
[ 0.000000] .data : 0xc04dc000 - 0xc0522c90 ( 284 kB)
[ 0.000000] .bss : 0xc0522cb4 - 0xc09de540 (4847 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3679 kB
[ 0.000000] per task-struct memory footprint: 1152 bytes
[ 0.000000] ODEBUG: 0 of 0 active objects replaced
[ 19.761274] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 19.842555] pid_max: default: 32768 minimum: 301
[ 19.844118] Mount-cache hash table entries: 512
[ 19.849737] Initializing cgroup subsys cpuacct
[ 19.849759] Initializing cgroup subsys devices
[ 19.849798] Initializing cgroup subsys freezer
[ 19.849841] Initializing cgroup subsys net_cls
[ 19.849877] Initializing cgroup subsys blkio
[ 19.849892] Initializing cgroup subsys perf_event
[ 19.849944] Initializing cgroup subsys bfqio
[ 19.850495] CPU: Testing write buffer coherency: ok
[ 19.851843] Setting up static identity map for 0x3540c8 - 0x354104
[ 19.858728] devtmpfs: initialized
[ 19.882001] NET: Registered protocol family 16
[ 19.883650] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 19.889409] Kirkwood: MV88F6281-A1, TCLK=200000000.
[ 19.889431] Feroceon L2: Enabling L2
[ 19.889470] Feroceon L2: Cache support initialised.
[ 19.896684] initial MPP regs: 01111111 11113322 00001111 00100000 00000000 00000000 00000000
[ 19.889470] Feroceon L2: Cache support initialised.
[ 19.896684] initial MPP regs: 01111111 11113322 00001111 00100000 00000000 00000000 00000000
[ 19.896724] final MPP regs: 01111111 11113322 00001111 00000000 00000000 00000000 00000000
[ 19.928261] bio: create slab <bio-0> at 0
[ 19.931042] vgaarb: loaded
[ 19.935186] SCSI subsystem initialized
[ 19.936110] libata version 3.00 loaded.
[ 19.937995] usbcore: registered new interface driver usbfs
[ 19.938465] usbcore: registered new interface driver hub
[ 19.939018] usbcore: registered new device driver usb
[ 19.944248] Switching to clocksource orion_clocksource
[ 20.070789] FS-Cache: Loaded
[ 20.134967] NET: Registered protocol family 2
[ 20.137930] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 20.138187] TCP bind hash table entries: 4096 (order: 5, 147456 bytes)
[ 20.138877] TCP: Hash tables configured (established 4096 bind 4096)
[ 20.139148] TCP: reno registered
[ 20.139175] UDP hash table entries: 256 (order: 2, 20480 bytes)
[ 20.139283] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[ 20.140659] NET: Registered protocol family 1
[ 20.140834] PCI: CLS 0 bytes, default 32
[ 20.142514] Trying to unpack rootfs image as initramfs...
[ 20.645554] Freeing initrd memory: 4652K
[ 20.649323] audit: initializing netlink socket (disabled)
[ 20.649607] type=2000 audit(0.890:1): initialized
[ 20.809497] VFS: Disk quotas dquot_6.5.2
[ 20.810517] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 20.825910] msgmni has been set to 233
[ 20.830556] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 20.830612] io scheduler noop registered
[ 20.830623] io scheduler deadline registered
[ 20.832452] io scheduler cfq registered
[ 20.834241] io scheduler bfq registered (default)
[ 20.835226] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[ 20.835489] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[ 20.875351] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 20.915351] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 20.955348] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[ 20.995350] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[ 21.022417] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 21.046987] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 21.047475] console [ttyS0] enabled
[ 21.093628] brd: module loaded
[ 21.116995] loop: module loaded
[ 21.122701] ONFI param page 0 valid
[ 21.122714] ONFI flash detected
[ 21.122729] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD), page size: 2048, OOB size: 64
[ 21.122812] Scanning device for bad blocks
[ 21.235662] Bad eraseblock 1036 at 0x000008180000
[ 21.345666] 4 cmdlinepart partitions found on MTD device orion_nand
[ 21.345678] Creating 4 MTD partitions on "orion_nand":
[ 21.345740] 0x000000000000-0x000000100000 : "u-boot"
[ 21.348275] 0x000000100000-0x000000500000 : "uImage"
[ 21.350252] 0x000000500000-0x000002500000 : "rootfs"
[ 21.352540] 0x000002500000-0x000010000000 : "data"
[ 21.357433] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 21.358256] libphy: mv643xx_eth smi: probed
[ 21.378969] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 02:50:43:67:b3:61
[ 21.379168] pch_gbe: EG20T PCH Gigabit Ethernet Driver - version 1.01
[ 21.379694] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 21.379994] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 21.380341] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 21.404425] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 21.424323] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 21.429096] hub 1-0:1.0: USB hub found
[ 21.429302] hub 1-0:1.0: 1 port detected
[ 21.429096] hub 1-0:1.0: USB hub found
[ 21.429302] hub 1-0:1.0: 1 port detected
[ 21.432646] Initializing USB Mass Storage driver...
[ 21.433183] usbcore: registered new interface driver usb-storage
[ 21.433195] USB Mass Storage support registered.
[ 21.434474] Registered led device: status:green:health
[ 21.435238] Registered led device: status:orange:fault
[ 21.435983] Registered led device: status:white:left0
[ 21.436744] Registered led device: status:white:left1
[ 21.437489] Registered led device: status:white:left2
[ 21.438227] Registered led device: status:white:left3
[ 21.438987] Registered led device: status:white:right0
[ 21.439760] Registered led device: status:white:right1
[ 21.440500] Registered led device: status:white:right2
[ 21.441279] Registered led device: status:white:right3
[ 21.443066] gre: GRE over IPv4 demultiplexor driver
[ 21.443362] TCP: cubic registered
[ 21.443380] NET: Registered protocol family 17
[ 21.443781] lib80211: common routines for IEEE802.11 drivers
[ 21.443856] lib80211_crypt: registered algorithm 'NULL'
[ 21.444206] Key type dns_resolver registered
[ 21.449513] console [netcon0] enabled
[ 21.449525] netconsole: network logging started
[ 21.452017] Freeing init memory: 152K
[ 21.605869] udevd[47]: starting version 175
[ 22.111065] sata_mv sata_mv.0: version 1.28
[ 22.111368] sata_mv sata_mv.0: cannot get optional clkdev
[ 22.111673] sata_mv sata_mv.0: slots 32 ports 2
[ 22.352966] scsi0 : sata_mv
[ 22.457324] scsi1 : sata_mv
[ 22.459504] ata1: SATA max UDMA/133 irq 21
[ 22.459519] ata2: SATA max UDMA/133 irq 21
[ 22.964793] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 22.984947] ata1.00: HPA detected: current 1953523055, native 1953525168
[ 22.984974] ata1.00: ATA-7: SAMSUNG HD103UJ, 1AA01113, max UDMA7
[ 22.984986] ata1.00: 1953523055 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 22.985133] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 23.004801] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 23.004830] ata1.00: configured for UDMA/133
[ 23.006775] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD103UJ 1AA0 PQ: 0 ANSI: 5
[ 23.011109] sd 0:0:0:0: [sda] 1953523055 512-byte logical blocks: (1.00 TB/931 GiB)
[ 23.013133] sd 0:0:0:0: [sda] Write Protect is off
[ 23.013151] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 23.013995] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 23.042697] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 23.066240] sda: sda1 sda2 sda3 sda4
[ 23.108921] sd 0:0:0:0: [sda] Attached SCSI disk
[ 23.404332] ata2: SATA link down (SStatus 0 SControl F300)
[ 23.480400] ata2: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xe frozen
[ 23.494486] ata2: edma_err_cause=00000010 pp_flags=00000000, dev connect
[ 23.501230] ata2: SError: { PHYRdyChg DevExch }
[ 23.514217] ata2: hard resetting link
[ 24.424351] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 24.425526] ata2.15: Port Multiplier 1.1, 0x1095:0x3726 r23, 6 ports, feat 0x1/0x9
[ 24.574826] ata2.00: hard resetting link
[ 25.084621] ata2.01: hard resetting link
[ 25.594618] ata2.02: hard resetting link
[ 26.104617] ata2.03: hard resetting link
[ 26.614617] ata2.04: hard resetting link
[ 27.124616] ata2.05: hard resetting link
[ 27.514357] ata2.00: ATA-8: ST3000DM001-1CH166, CC44, max UDMA/133
[ 27.514373] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 27.534346] ata2.00: failed to get Identify Device Data, Emask 0x1
[ 27.664360] ata2.00: failed to get Identify Device Data, Emask 0x1
[ 27.664393] ata2.00: configured for UDMA/133
[ 27.704365] ata2.01: ATA-8: ST3000DM001-1CH166, CC43, max UDMA/133
[ 27.664393] ata2.00: configured for UDMA/133
[ 27.704365] ata2.01: ATA-8: ST3000DM001-1CH166, CC43, max UDMA/133
[ 27.704381] ata2.01: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 27.724356] ata2.01: failed to get Identify Device Data, Emask 0x1
[ 27.804355] ata2.01: failed to get Identify Device Data, Emask 0x1
[ 27.804377] ata2.01: configured for UDMA/133
[ 27.844362] ata2.02: ATA-8: ST2000DL003-9VT166, CC3C, max UDMA/133
[ 27.844376] ata2.02: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 27.864356] ata2.02: failed to get Identify Device Data, Emask 0x1
[ 27.944355] ata2.02: failed to get Identify Device Data, Emask 0x1
[ 27.944376] ata2.02: configured for UDMA/133
[ 27.984362] ata2.03: ATA-8: ST3000DM001-1CH166, CC43, max UDMA/133
[ 27.984377] ata2.03: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 28.004354] ata2.03: failed to get Identify Device Data, Emask 0x1
[ 28.084358] ata2.03: failed to get Identify Device Data, Emask 0x1
[ 28.084379] ata2.03: configured for UDMA/133
[ 28.124361] ata2.04: ATA-8: ST3000DM001-1CH166, CC44, max UDMA/133
[ 28.124375] ata2.04: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 28.344358] ata2.04: failed to get Identify Device Data, Emask 0x1
[ 28.424355] ata2.04: failed to get Identify Device Data, Emask 0x1
[ 28.424377] ata2.04: configured for UDMA/133
[ 28.424640] ata2: EH complete
[ 28.426091] scsi 1:0:0:0: Direct-Access ATA ST3000DM001-1CH1 CC44 PQ: 0 ANSI: 5
[ 28.438531] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 28.438550] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 28.440559] sd 1:0:0:0: [sdb] Write Protect is off
[ 28.440577] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 28.441391] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 28.455103] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 28.461109] scsi 1:1:0:0: Direct-Access ATA ST3000DM001-1CH1 CC43 PQ: 0 ANSI: 5
[ 28.475308] sd 1:1:0:0: [sdc] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 28.475328] sd 1:1:0:0: [sdc] 4096-byte physical blocks
[ 28.477324] sd 1:1:0:0: [sdc] Write Protect is off
[ 28.477343] sd 1:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 28.478150] sd 1:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 28.512317] sd 1:1:0:0: Attached scsi generic sg2 type 0
[ 28.521477] sdb: sdb1
[ 28.525188] scsi 1:2:0:0: Direct-Access ATA ST2000DL003-9VT1 CC3C PQ: 0 ANSI: 5
[ 28.539048] sd 1:2:0:0: [sdd] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 28.539067] sd 1:2:0:0: [sdd] 4096-byte physical blocks
[ 28.541059] sd 1:2:0:0: [sdd] Write Protect is off
[ 28.541078] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 28.541882] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 28.565037] sd 1:2:0:0: Attached scsi generic sg3 type 0
[ 28.565682] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 28.582004] sdc: sdc1
[ 28.590826] sdd: sdd1
[ 28.607630] scsi 1:3:0:0: Direct-Access ATA ST3000DM001-1CH1 CC43 PQ: 0 ANSI: 5
[ 28.611443] sd 1:3:0:0: [sde] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 28.611459] sd 1:3:0:0: [sde] 4096-byte physical blocks
[ 28.613434] sd 1:3:0:0: [sde] Write Protect is off
[ 28.613452] sd 1:3:0:0: [sde] Mode Sense: 00 3a 00 00
[ 28.614250] sd 1:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 28.635081] sd 1:1:0:0: [sdc] Attached SCSI disk
[ 28.656215] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 28.658528] sd 1:3:0:0: Attached scsi generic sg4 type 0
[ 28.684897] scsi 1:4:0:0: Direct-Access ATA ST3000DM001-1CH1 CC44 PQ: 0 ANSI: 5
[ 28.688702] sd 1:4:0:0: [sdf] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 28.688720] sd 1:4:0:0: [sdf] 4096-byte physical blocks
[ 28.690738] sd 1:4:0:0: [sdf] Write Protect is off
[ 28.690756] sd 1:4:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 28.691571] sd 1:4:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 28.728952] sd 1:4:0:0: Attached scsi generic sg5 type 0
[ 28.732931] sde: sde1
[ 28.776384] sd 1:3:0:0: [sde] Attached SCSI disk
[ 28.826574] sdf: sdf1
[ 28.776384] sd 1:3:0:0: [sde] Attached SCSI disk
[ 28.826574] sdf: sdf1
[ 28.853920] sd 1:4:0:0: [sdf] Attached SCSI disk
[ 34.459284] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
[ 37.065743] udevd[301]: starting version 175
[ 44.094180] md: md0 stopped.
[ 44.146249] unwind: Index not found bf024878
[ 44.146307] unwind: Index not found bf024878
[ 44.146415] unwind: Index not found bf024878
[ 44.146477] unwind: Index not found bf024878
[ 44.146816] unwind: Index not found bf024878
[ 44.148836] unwind: Index not found bf024878
[ 44.148865] md: bind<sdc1>
[ 44.148893] unwind: Index not found bf024900
[ 44.148927] unwind: Index not found bf024900
[ 44.148955] unwind: Index not found bf024900
[ 44.148998] unwind: Index not found bf024900
[ 44.149034] unwind: Index not found bf024900
[ 44.149070] unwind: Index not found bf024900
[ 44.149104] unwind: Index not found bf024900
[ 44.149139] unwind: Index not found bf024900
[ 44.149173] unwind: Index not found bf024900
[ 44.149207] unwind: Index not found bf024900
[ 44.149240] unwind: Index not found bf024900
[ 44.149274] unwind: Index not found bf024900
[ 44.149310] unwind: Index not found bf024900
[ 44.149334] unwind: Index not found bf024900
[ 44.149371] unwind: Index not found bf024900
[ 44.149399] unwind: Index not found bf024900
[ 44.149436] unwind: Index not found bf024900
[ 44.149491] unwind: Index not found bf024900
[ 44.149520] unwind: Index not found bf024900
[ 44.164508] unwind: Index not found bf024878
[ 44.164568] unwind: Index not found bf024878
[ 44.164676] unwind: Index not found bf024878
[ 44.164738] unwind: Index not found bf024878
[ 44.166928] unwind: Index not found bf024878
[ 44.166960] md: bind<sdb1>
[ 44.166989] unwind: Index not found bf024900
[ 44.167025] unwind: Index not found bf024900
[ 44.167054] unwind: Index not found bf024900
[ 44.167098] unwind: Index not found bf024900
[ 44.167135] unwind: Index not found bf024900
[ 44.167170] unwind: Index not found bf024900
[ 44.167205] unwind: Index not found bf024900
[ 44.167240] unwind: Index not found bf024900
[ 44.167275] unwind: Index not found bf024900
[ 44.167309] unwind: Index not found bf024900
[ 44.167344] unwind: Index not found bf024900
[ 44.167378] unwind: Index not found bf024900
[ 44.167414] unwind: Index not found bf024900
[ 44.167440] unwind: Index not found bf024900
[ 44.167477] unwind: Index not found bf024900
[ 44.167506] unwind: Index not found bf024900
[ 44.167532] unwind: Index not found bf024900
[ 44.167567] unwind: Index not found bf024900
[ 44.167594] unwind: Index not found bf024900
[ 44.168221] unwind: Index not found bf024878
[ 44.168275] unwind: Index not found bf024878
[ 44.168370] unwind: Index not found bf024878
[ 44.168424] unwind: Index not found bf024878
[ 44.174478] unwind: Index not found bf024878
[ 44.174511] md: bind<sdf1>
[ 44.174539] unwind: Index not found bf024900
[ 44.174573] unwind: Index not found bf024900
[ 44.174602] unwind: Index not found bf024900
[ 44.174573] unwind: Index not found bf024900
[ 44.174602] unwind: Index not found bf024900
[ 44.174657] unwind: Index not found bf024900
[ 44.174696] unwind: Index not found bf024900
[ 44.174732] unwind: Index not found bf024900
[ 44.174768] unwind: Index not found bf024900
[ 44.174804] unwind: Index not found bf024900
[ 44.174838] unwind: Index not found bf024900
[ 44.174873] unwind: Index not found bf024900
[ 44.174907] unwind: Index not found bf024900
[ 44.174941] unwind: Index not found bf024900
[ 44.174978] unwind: Index not found bf024900
[ 44.175003] unwind: Index not found bf024900
[ 44.175042] unwind: Index not found bf024900
[ 44.175071] unwind: Index not found bf024900
[ 44.175095] unwind: Index not found bf024900
[ 44.175130] unwind: Index not found bf024900
[ 44.175156] unwind: Index not found bf024900
[ 44.182389] unwind: Index not found bf024878
[ 44.182447] unwind: Index not found bf024878
[ 44.182550] unwind: Index not found bf024878
[ 44.182612] unwind: Index not found bf024878
[ 44.184496] unwind: Index not found bf024878
[ 44.184528] md: bind<sde1>
[ 44.184556] unwind: Index not found bf024900
[ 44.184590] unwind: Index not found bf024900
[ 44.184618] unwind: Index not found bf024900
[ 44.184659] unwind: Index not found bf024900
[ 44.184695] unwind: Index not found bf024900
[ 44.184729] unwind: Index not found bf024900
[ 44.184777] unwind: Index not found bf024900
[ 44.184816] unwind: Index not found bf024900
[ 44.184852] unwind: Index not found bf024900
[ 44.184888] unwind: Index not found bf024900
[ 44.184923] unwind: Index not found bf024900
[ 44.184958] unwind: Index not found bf024900
[ 44.184995] unwind: Index not found bf024900
[ 44.185020] unwind: Index not found bf024900
[ 44.185059] unwind: Index not found bf024900
[ 44.185087] unwind: Index not found bf024900
[ 44.185111] unwind: Index not found bf024900
[ 44.185147] unwind: Index not found bf024900
[ 44.185172] unwind: Index not found bf024900
[ 44.495768] raid6: int32x1 80 MB/s
[ 44.689044] raid6: int32x2 122 MB/s
[ 44.854313] raid6: int32x4 123 MB/s
[ 45.025138] raid6: int32x8 155 MB/s
[ 45.025150] raid6: using algorithm int32x8 (155 MB/s)
[ 45.025158] raid6: using intx1 recovery algorithm
[ 45.039077] async_tx: api initialized (async)
[ 45.047580] xor: measuring software checksum speed
[ 45.144294] arm4regs : 1071.600 MB/sec
[ 45.244292] 8regs : 650.800 MB/sec
[ 45.344991] 32regs : 900.800 MB/sec
[ 45.345004] xor: using function: arm4regs (1071.600 MB/sec)
[ 45.383360] md: raid6 personality registered for level 6
[ 45.383377] md: raid5 personality registered for level 5
[ 45.383386] md: raid4 personality registered for level 4
[ 45.386887] md/raid:md0: device sde1 operational as raid disk 0
[ 45.386904] md/raid:md0: device sdf1 operational as raid disk 3
[ 45.386914] md/raid:md0: device sdb1 operational as raid disk 2
[ 45.386924] md/raid:md0: device sdc1 operational as raid disk 1
[ 45.402277] md/raid:md0: allocated 4260kB
[ 45.402608] md/raid:md0: raid level 5 active with 4 out of 4 devices, algorithm 2
[ 45.402620] RAID conf printout:
[ 45.402629] --- level:5 rd:4 wd:4
[ 45.402620] RAID conf printout:
[ 45.402629] --- level:5 rd:4 wd:4
[ 45.402639] disk 0, o:1, dev:sde1
[ 45.402649] disk 1, o:1, dev:sdc1
[ 45.402658] disk 2, o:1, dev:sdb1
[ 45.402667] disk 3, o:1, dev:sdf1
[ 45.403598] md0: detected capacity change from 0 to 9001370124288
[ 45.463576] md0: unknown partition table
[ 46.459812] Adding 262140k swap on /dev/sda2. Priority:1 extents:1 across:262140k
[ 46.663020] EXT4-fs (sda4): re-mounted. Opts: (null)
[ 47.443305] EXT4-fs (sda4): re-mounted. Opts: (null)
[ 48.400112] cryptodev: driver 1.5 loaded.
[ 55.110943] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 58.343841] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null)
[ 64.697917] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled

')