[SOLVED]PPV4:USB Wireless Adapter Cannot work on USB3.0 Port

This forum is for Marvell Kirkwood devices such as the GoFlex Home/Net, PogoPlug v1/v2, SheevaPlug, and ZyXEL devices.
Topic locked

[SOLVED]PPV4:USB Wireless Adapter Cannot work on USB3.0 Port

Postby suyanlu » Fri Apr 12, 2013 2:19 pm

On my pogoplug series4(PPV4), My USB Wireless Adapter cannot work on USB3.0 Port, but if woking fine on USB2.0.
This Adapter I used on GoFlexHome(USB2.0 only) is OK.
I change other USB Adapter to PPV4, the same error appeared on USB3.0 Port, BUT OK on USB2.0,too.
System Info:
$this->bbcode_second_pass_code('', '
Linux pogoplugv4 3.1.10-17-ARCH #1 PREEMPT Sat Apr 6 21:30:51 UTC 2013 armv5tel GNU/Linux
')
Log Message Following:
$this->bbcode_second_pass_code('', '
Apr 12 22:05:31 pogoplugv4 kernel: [ 150.343645] usb 2-2: new high speed USB device number 4 using xhci_hcd
Apr 12 22:05:31 pogoplugv4 kernel: [ 150.363937] xhci_hcd 0000:00:01.0: WARN: short transfer on control ep
Apr 12 22:05:31 pogoplugv4 kernel: [ 150.364005] xhci_hcd 0000:00:01.0: WARN: short transfer on control ep
Apr 12 22:05:31 pogoplugv4 kernel: [ 150.365040] hub 2-2:1.0: USB hub found
Apr 12 22:05:31 pogoplugv4 kernel: [ 150.365092] xhci_hcd 0000:00:01.0: WARN: short transfer on control ep
Apr 12 22:05:31 pogoplugv4 kernel: [ 150.365139] hub 2-2:1.0: 7 ports detected
Apr 12 22:05:31 pogoplugv4 kernel: [ 150.643679] usb 2-2.5: new high speed USB device number 5 using xhci_hcd
Apr 12 22:05:31 pogoplugv4 kernel: [ 150.674037] xhci_hcd 0000:00:01.0: WARN: short transfer on control ep
Apr 12 22:05:31 pogoplugv4 kernel: [ 150.674126] xhci_hcd 0000:00:01.0: WARN: short transfer on control ep
Apr 12 22:05:31 pogoplugv4 kernel: [ 150.674217] xhci_hcd 0000:00:01.0: WARN: short transfer on control ep
Apr 12 22:05:31 pogoplugv4 kernel: [ 150.674301] xhci_hcd 0000:00:01.0: WARN: short transfer on control ep
Apr 12 22:05:31 pogoplugv4 kernel: [ 150.962751] usb 2-2.5: ath9k_htc: Transferred FW: htc_9271.fw, size: 51272
Apr 12 22:05:31 pogoplugv4 kernel: [ 151.115801] ath9k_htc: probe of 2-2.5:1.0 failed with error -22
Apr 12 22:05:59 pogoplugv4 kernel: [ 178.377682] usb 2-2: USB disconnect, device number 4
Apr 12 22:05:59 pogoplugv4 kernel: [ 178.377704] usb 2-2.5: USB disconnect, device number 5
Apr 12 22:06:22 pogoplugv4 kernel: [ 201.843645] usb 2-1: new high speed USB device number 6 using xhci_hcd
Apr 12 22:06:22 pogoplugv4 kernel: [ 201.864554] xhci_hcd 0000:00:01.0: WARN: short transfer on control ep
Apr 12 22:06:22 pogoplugv4 kernel: [ 201.864802] xhci_hcd 0000:00:01.0: WARN: short transfer on control ep
Apr 12 22:06:22 pogoplugv4 kernel: [ 201.864971] xhci_hcd 0000:00:01.0: WARN: short transfer on control ep
Apr 12 22:06:22 pogoplugv4 kernel: [ 201.865182] xhci_hcd 0000:00:01.0: WARN: short transfer on control ep
Apr 12 22:06:47 pogoplugv4 kernel: [ 227.088225] usb 2-1: USB disconnect, device number 6
')

AnyBody can help ?
3ks.
Last edited by suyanlu on Wed Apr 17, 2013 1:54 pm, edited 1 time in total.
suyanlu
 
Posts: 31
Joined: Fri Mar 15, 2013 9:33 am
Top

Re: [Bug]PPV4:USB Wireless Adapter Cannot work on USB3.0 Por

Postby moonman » Fri Apr 12, 2013 8:19 pm

See if updating your kernel will help (pacman -Sy linux-kirkwood linux-headers-kirkwood)
Pogoplug V4 | GoFlex Home | Raspberry Pi 4 4GB | CuBox-i4 Pro | ClearFog | BeagleBone Black | Odroid U2 | Odroid C1 | Odroid XU4
-----------------------------------------------------------------------------------------------------------------------
[armv5] Updated U-Boot | [armv5] NAND Rescue System
moonman
Developer
 
Posts: 3388
Joined: Sat Jan 15, 2011 3:36 am
Top

Re: [Bug]PPV4:USB Wireless Adapter Cannot work on USB3.0 Por

Postby suyanlu » Sat Apr 13, 2013 2:09 am

Yes, I update all system using pacman -Syu, this command update kernel ?
suyanlu
 
Posts: 31
Joined: Fri Mar 15, 2013 9:33 am
Top

Re: [Bug]PPV4:USB Wireless Adapter Cannot work on USB3.0 Por

Postby suyanlu » Sat Apr 13, 2013 2:34 am

$this->bbcode_second_pass_quote('moonman', 'S')ee if updating your kernel will help (pacman -Sy linux-kirkwood linux-headers-kirkwood)

Thank you , moonman.
It's woking now after update kernel to 3.8.6
suyanlu
 
Posts: 31
Joined: Fri Mar 15, 2013 9:33 am
Top

Re: [Bug]PPV4:USB Wireless Adapter Cannot work on USB3.0 Por

Postby suyanlu » Mon Apr 15, 2013 4:16 pm

$this->bbcode_second_pass_quote('moonman', 'S')ee if updating your kernel will help (pacman -Sy linux-kirkwood linux-headers-kirkwood)


hi, moonman,
I find other problem on ppv4 about usb wireless adapter.
if I power off (unplug power adapter), replug power adapter, boot, usb wireless adapter is ok.
if I use "reboot" command to reboot system, usb wireless cannot working(USB 3.0 Port).
if I unplug usb wireless adapter when running OK, then plug usb wireless adapter on, it's load failed.

Log Message following:
$this->bbcode_second_pass_code('', '
pr 15 08:09:26 pogoplugv4 kernel: [34167.865246] usb 2-1: USB disconnect, device number 2
Apr 15 08:09:26 pogoplugv4 kernel: [34167.866452] wlan0: deauthenticating from 14:e6:e4:83:e7:58 by local choice (reason=3)
Apr 15 08:09:27 pogoplugv4 kernel: [34168.661539] cfg80211: Calling CRDA for country: CN
Apr 15 08:09:28 pogoplugv4 kernel: [34169.396387] usb 2-1: ath9k_htc: USB layer deinitialized
Apr 15 08:09:28 pogoplugv4 dhcpcd[377]: wlan0: carrier lost
Apr 15 08:09:28 pogoplugv4 dhcpcd[377]: wlan0: removing interface
Apr 15 10:27:41 pogoplugv4 ntpd[388]: skew change -8.798 exceeds limit
Apr 15 21:00:58 pogoplugv4 kernel: [80463.089264] usb 2-1: new high-speed USB device number 3 using xhci_hcd
Apr 15 21:00:58 pogoplugv4 kernel: [80463.121253] usb 2-1: ath9k_htc: Firmware htc_9271.fw requested
Apr 15 21:00:58 pogoplugv4 kernel: [80463.611594] usb 2-1: ath9k_htc: Transferred FW: htc_9271.fw, size: 51272
Apr 15 21:00:59 pogoplugv4 kernel: [80463.847717] ath9k_htc 2-1:1.0: ath9k_htc: HTC initialized with 33 credits
Apr 15 21:00:59 pogoplugv4 kernel: [80464.079227] ath9k_htc 2-1:1.0: ath9k_htc: FW Version: 1.3
Apr 15 21:00:59 pogoplugv4 kernel: [80464.085600] ieee80211 phy1: Atheros AR9271 Rev:1
Apr 15 21:00:59 pogoplugv4 systemd-sysctl[3056]: Duplicate assignment of kernel/sysrq in file '/usr/lib/sysctl.d/50-default.conf',
ignoring.
Apr 15 21:00:59 pogoplugv4 kernel: [80464.516258] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Apr 15 21:01:00 pogoplugv4 kernel: [80465.656556] wlan0: authenticate with 14:e6:e4:83:e7:58
Apr 15 21:01:01 pogoplugv4 kernel: [80465.866139] wlan0: send auth to 14:e6:e4:83:e7:58 (try 1/3)
Apr 15 21:01:01 pogoplugv4 kernel: [80465.868311] wlan0: authenticated
Apr 15 21:01:01 pogoplugv4 kernel: [80465.869487] wlan0: associate with 14:e6:e4:83:e7:58 (try 1/3)
Apr 15 21:01:01 pogoplugv4 kernel: [80465.873186] wlan0: RX AssocResp from 14:e6:e4:83:e7:58 (capab=0x431 status=0 aid=5)
Apr 15 21:01:01 pogoplugv4 kernel: [80465.880768] wlan0: associated
Apr 15 21:01:01 pogoplugv4 kernel: [80465.880900] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
')

And Normal Initializing Process:
$this->bbcode_second_pass_code('', '
Apr 15 21:48:57 pogoplugv4 kernel: [83342.916428] wlan0: deauthenticating from 14:e6:e4:83:e7:58 by local choice (reason=3)
Apr 15 21:48:58 pogoplugv4 kernel: [83343.163184] cfg80211: Calling CRDA to update world regulatory domain
Apr 15 21:49:05 pogoplugv4 kernel: [83350.701994] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Apr 15 21:49:07 pogoplugv4 kernel: [83352.107275] wlan0: authenticate with 14:e6:e4:83:e7:58
Apr 15 21:49:07 pogoplugv4 kernel: [83352.335583] wlan0: send auth to 14:e6:e4:83:e7:58 (try 1/3)
Apr 15 21:49:07 pogoplugv4 kernel: [83352.337787] wlan0: authenticated
Apr 15 21:49:07 pogoplugv4 kernel: [83352.346188] wlan0: associate with 14:e6:e4:83:e7:58 (try 1/3)
Apr 15 21:49:07 pogoplugv4 kernel: [83352.349834] wlan0: RX AssocResp from 14:e6:e4:83:e7:58 (capab=0x431 status=0 aid=5)
Apr 15 21:49:07 pogoplugv4 kernel: [83352.358979] wlan0: associated
Apr 15 21:49:07 pogoplugv4 kernel: [83352.359147] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Apr 15 21:49:08 pogoplugv4 dhcpcd[3443]: version 5.6.7 starting
Apr 15 21:49:09 pogoplugv4 dhcpcd[3443]: wlan0: sending IPv6 Router Solicitation
Apr 15 21:49:09 pogoplugv4 dhcpcd[3443]: wlan0: rebinding lease of 192.168.2.221
Apr 15 21:49:09 pogoplugv4 dhcpcd[3443]: wlan0: acknowledged 192.168.2.221 from 192.168.2.1
Apr 15 21:49:09 pogoplugv4 dhcpcd[3443]: wlan0: checking for 192.168.2.221
Apr 15 21:49:13 pogoplugv4 dhcpcd[3443]: wlan0: sending IPv6 Router Solicitation
Apr 15 21:49:14 pogoplugv4 dhcpcd[3443]: wlan0: leased 192.168.2.221 for 6048000 seconds
Apr 15 21:49:14 pogoplugv4 dhcpcd[3443]: forked to background, child pid 3450
Apr 15 21:49:17 pogoplugv4 dhcpcd[3450]: wlan0: sending IPv6 Router Solicitation
Apr 15 21:49:21 pogoplugv4 dhcpcd[3450]: wlan0: sending IPv6 Router Solicitation
Apr 15 21:49:21 pogoplugv4 dhcpcd[3450]: wlan0: no IPv6 Routers available
')

it's looked like link is ok, but dhcp not working?
my netcfg profile like this:
$this->bbcode_second_pass_code('', '
┌─[root@pogoplugv4]─[/etc/network.d]
└──> ls
examples interfaces wired-dhcp-eth0 wired-eth0 wired-static-eth0 wireless-dhcp-wlan0 wireless-wlan0
┌─[root@pogoplugv4]─[/etc/network.d]
└──> cat wireless-dhcp-wlan0
CONNECTION='wireless'
INTERFACE=wlan0
SECURITY='wpa-configsection'
IP='dhcp'
DNS=('192.168.1.1')

CONFIGSECTION='
ssid="33604"
psk="pskpskpskpsk"'
')
suyanlu
 
Posts: 31
Joined: Fri Mar 15, 2013 9:33 am
Top
Topic locked

Return to Marvell Kirkwood

Who is online

Users browsing this forum: No registered users and 15 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group    © Arch Linux ARM