GoFlex Home won't boot from USB with SATA plugged in

[jcconnell]

Well, I'm back to booting from USB. This has been great for the learns.

I followed the Doozan guide here to get back to reinstall uBoot: http://forum.doozan.com/read.php?3,6965

I then tried installing alarm to the SATA again with these partitions
/dev/sda1 +10G rootfs, boot, ext3
/dev/sda2 +1G swap
/dev/sda3 the rest

No such luck. Back to troubleshooting and running off the USB drive.

I'm using a USB drive that I created following your guide.
$this->bbcode_second_pass_code('', '[root@alarm ~]# uname -a
Linux alarm 3.9.2-1-ARCH #1 PREEMPT Mon May 13 00:02:00 UTC 2013 armv5tel GNU/Linux')

[jcconnell]

Ok, booted from USB. Connected SATA after boot. Left partitions and files mentioned in previous posts intact.

Ran Jeff's uBoot updater script listed here: http://forum.doozan.com/read.php?3,6965,8189#msg-8189

Followed some steps from your (moonman) thread here: viewtopic.php?f=18&t=3355
$this->bbcode_second_pass_code('', '
/usr/sbin/fw_setenv arcNumber 3338
/usr/sbin/fw_setenv sata_device '0:1'
/usr/sbin/fw_setenv sata_root '/dev/sda1'
/usr/sbin/fw_setenv sata_rootfstype 'ext3'
/usr/sbin/fw_setenv sata_rootdelay '10'
/usr/sbin/fw_setenv sata_set_bootargs 'setenv bootargs console=$console root=$sata_root rootdelay=$sata_rootdelay rootfstype=$sata_rootfstype $mtdparts $sata_custom_params'
/usr/sbin/fw_setenv sata_boot 'ide reset; mw 0x800000 0 1; ext2load ide $sata_device 0x800000 /boot/uImage; if ext2load ide $sata_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi'
/usr/sbin/fw_setenv sata_bootcmd 'run sata_set_bootargs; run sata_boot'
/usr/sbin/fw_setenv bootcmd 'run sata_bootcmd; usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset'

#U-BOOT Netconsole
/usr/sbin/fw_setenv ipaddr '10.10.10.6'
/usr/sbin/fw_setenv ncip '10.10.10.5'
/usr/sbin/fw_setenv ncipk '10.10.10.4'
/usr/sbin/fw_setenv serverip '10.10.10.3'
/usr/sbin/fw_setenv preboot 'run nc_test nc_start'
/usr/sbin/fw_setenv nc_test 'ping $ncip'
/usr/sbin/fw_setenv nc_start 'setenv stdin nc; setenv stdout nc; setenv stderr nc; version'
#Kernel Netconsole:
#When booting from USB
/usr/sbin/fw_setenv usb_custom_params 'ignore_loglevel netconsole=6665@10.10.10.3/eth0,6666@10.10.10.4/'
#When booting from SATA
/usr/sbin/fw_setenv sata_custom_params 'ignore_loglevel netconsole=6665@10.10.10.3/eth0,6666@10.10.10.4/'
/usr/sbin/fw_setenv usb_custom_params 'ignore_loglevel netconsole=6665@10.10.10.3/eth0,6666@10.10.10.4/ elevator=bfq'
/usr/sbin/fw_setenv sata_custom_params 'ignore_loglevel netconsole=6665@10.10.10.3/eth0,6666@10.10.10.4/ elevator=bfq'')

Booted with SATA and USB just fine. Booted with just SATA fine as well.

For reference, here is my printenv:
$this->bbcode_second_pass_code('', '[root@alarm ~]# fw_printenv
ethact=egiga0
bootdelay=3
baudrate=115200
mainlineLinux=yes
console=ttyS0,115200
led_init=green blinking
led_exit=green off
led_error=orange blinking
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
mtdids=nand0=orion_nand
partition=nand0,2
stdin=serial
stdout=serial
stderr=serial
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_list=1 2 3 4
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_init=run usb_scan
usb_device=0:1
usb_root=/dev/sda1
usb_rootfstype=ext2
usb_rootdelay=10
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
ethaddr=02:50:43:92:a6:65
arcNumber=3338
sata_device=0:1
sata_root=/dev/sda1
sata_rootfstype=ext3
sata_rootdelay=10
sata_set_bootargs=setenv bootargs console=$console root=$sata_root rootdelay=$sata_rootdelay rootfstype=$sata_rootfstype $mtdparts $sata_custom_params
sata_boot=ide reset; mw 0x800000 0 1; ext2load ide $sata_device 0x800000 /boot/uImage; if ext2load ide $sata_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
sata_bootcmd=run sata_set_bootargs; run sata_boot
bootcmd=run sata_bootcmd; usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
ipaddr=10.10.10.6
ncip=10.10.10.5
ncipk=10.10.10.4
serverip=10.10.10.3
preboot=run nc_test nc_start
nc_test=ping $ncip
nc_start=setenv stdin nc; setenv stdout nc; setenv stderr nc; version
usb_custom_params=ignore_loglevel netconsole=6665@10.10.10.3/eth0,6666@10.10.10.4/ elevator=bfq
sata_custom_params=ignore_loglevel netconsole=6665@10.10.10.3/eth0,6666@10.10.10.4/ elevator=bfq
')

[moonman]

After you upgraded the u-boot did you setup the environment for sata boot?

[jcconnell]

I executed every command listed in the box above my printenv in the previous post. I just followed the instructions to boot from.SATA then USB.

[moonman]

Yeah I was writing my last post without seeing your last post Glad it worked