[resolved] dockstar blocks on end of kernel start

[crousti]

Hi guys,

this is my first post. I tried looking for an answer but so far could not find it.

I previously used a debian squeeze on a usb key, but wanted to tinker about with something lighter and different. Enters archLinux .

Now i have the latest Uboot, and I followed the steps on arch linux install. The "sync" step strangely lasted maybe 1 second or less ...

First i tried on a USB stick with ext3, and that would not work correctly; then i used a stick that i knew would work, in ext2, at it booted debian some hours ago.

But ... now it does not boot on the stick, and i have no idea why.

I believe you could help if i publish the environment and netconsole boot result, so here you go.


Edit : you can find the kernel netconsole trace on my second post. It ends en "Started Login Service." yet the dockstar is not found on the network
Thanks !

my printenv:
$this->bbcode_second_pass_code('', '
ethact=egiga0
bootdelay=3
baudrate=115200
mainlineLinux=yes
console=ttyS0,115200
led_init=green blinking
led_exit=green off
led_error=orange blinking
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
mtdids=nand0=orion_nand
partition=nand0,2
stdin=serial
stdout=serial
stderr=serial
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_list=1 2 3 4
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_init=run usb_scan
usb_device=0:1
usb_root=/dev/sda1
usb_rootdelay=10
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
ethaddr=00:10:75:1A:89:36
arcNumber=2097
serverip=172.20.0.159
ipaddr=172.20.0.127
if_netconsole=ping $serverip
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
preboot=run if_netconsole start_netconsole
usb_rootfstype=ext2
')

my net console:

$this->bbcode_second_pass_code('', '
U-Boot 2011.12 (Feb 12 2012 - 21:33:07)
Seagate FreeAgent DockStar
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt

** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1752
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
2888208 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
** File not found /boot/uInitrd
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-3.1.10-20-ARCH
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2888144 Bytes = 2.8 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...
')

It kind of hangs on Starting kernel.

[hydro]

By default the kernel doesn't send message on netconsole, you have to enable it.

[crousti]

ok, i enabled kernel netconsole, and it does not look like anything is wrong.
Yet the device is not found on the network : i used nmap to scan the whole subnet on port 22, and nothing pops out. Wireshark does not find anything either...


$this->bbcode_second_pass_code('', '
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.1.10-20-ARCH (nobody@panda1) (gcc version 4.7.2 (
GCC) ) #1 PREEMPT Sat May 18 14:37:07 UTC 2013
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397
7
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Seagate FreeAgent DockStar
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdela
y=10 rootfstype=ext2 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(dat
a) loglevel=7 netconsole=6666@172.20.0.127/eth0,6666@172.20.0.159/AC:16:2D:04:CF
:38
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] allocated 524288 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memor
y cgroups
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 122828k/122828k available, 8244k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xc8800000 - 0xfe800000 ( 864 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc05381b4 (5313 kB)
[ 0.000000] .init : 0xc0539000 - 0xc0564000 ( 172 kB)
[ 0.000000] .data : 0xc0564000 - 0xc059d2b0 ( 229 kB)
[ 0.000000] .bss : 0xc059d2d4 - 0xc066ae6c ( 823 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, N
odes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474
ms
[ 0.000000] Console: colour dummy device 80x30
[ 14.549400] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 14.639331] pid_max: default: 32768 minimum: 301
[ 14.639453] Security Framework initialized
[ 14.639479] AppArmor: AppArmor disabled by boot time parameter
[ 14.639546] Mount-cache hash table entries: 512
[ 14.639940] Initializing cgroup subsys cpuacct
[ 14.639968] Initializing cgroup subsys memory
[ 14.640006] Initializing cgroup subsys devices
[ 14.640019] Initializing cgroup subsys freezer
[ 14.640029] Initializing cgroup subsys net_cls
[ 14.640039] Initializing cgroup subsys blkio
[ 14.640064] Initializing cgroup subsys perf_event
[ 14.640083] Initializing cgroup subsys bfqio
[ 14.640176] CPU: Testing write buffer coherency: ok
[ 14.641483] devtmpfs: initialized
[ 14.643353] NET: Registered protocol family 16
[ 14.644015] Kirkwood: MV88F6281-A0, TCLK=200000000.
[ 14.644031] Feroceon L2: Enabling L2
[ 14.644068] Feroceon L2: Cache support initialised.
[ 14.649613] bio: create slab <bio-0> at 0
[ 14.649987] vgaarb: loaded
[ 14.650254] SCSI subsystem initialized
[ 14.650629] usbcore: registered new interface driver usbfs
[ 14.650727] usbcore: registered new interface driver hub
[ 14.650836] usbcore: registered new device driver usb
[ 14.651397] Switching to clocksource orion_clocksource
[ 14.659329] Switched to NOHz mode on CPU #0
[ 14.660385] FS-Cache: Loaded
[ 14.670398] NET: Registered protocol family 2
[ 14.670640] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 14.671351] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 14.671492] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 14.671547] TCP: Hash tables configured (established 4096 bind 4096)
[ 14.671558] TCP reno registered
[ 14.671569] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 14.671591] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 14.671835] NET: Registered protocol family 1
[ 14.672461] audit: initializing netlink socket (disabled)
[ 14.672495] type=2000 audit(0.120:1): initialized
[ 14.757527] VFS: Disk quotas dquot_6.5.2
[ 14.757808] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 14.760047] JFFS2 version 2.2. (NAND) ┬® 2001-2006 Red Hat, Inc.
[ 14.761378] aufs 3.1-20111107
[ 14.761400] msgmni has been set to 239
[ 14.762807] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2
53)
[ 14.762824] io scheduler noop registered
[ 14.762833] io scheduler deadline registered
[ 14.762914] io scheduler cfq registered
[ 14.762984] io scheduler bfq registered (default)
[ 14.763048] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[ 14.763082] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[ 14.801481] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 14.841490] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 14.881477] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[ 14.921477] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[ 14.926658] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 14.947353] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 15.432147] console [ttyS0] enabled
[ 15.441861] brd: module loaded
[ 15.447976] loop: module loaded
[ 15.452127] ONFI flash detected
[ 15.455373] ONFI param page 0 valid
[ 15.458881] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G
08AAD)
[ 15.466602] Scanning device for bad blocks
[ 15.623923] 4 cmdlinepart partitions found on MTD device orion_nand
[ 15.630216] Creating 4 MTD partitions on "orion_nand":
[ 15.635400] 0x000000000000-0x000000100000 : "u-boot"
[ 15.640740] 0x000000100000-0x000000500000 : "uImage"
[ 15.646069] 0x000000500000-0x000002500000 : "rootfs"
[ 15.651388] 0x000002500000-0x000010000000 : "data"
[ 15.657492] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 15.664445] mv643xx_eth smi: probed
[ 15.670094] mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC addres
s 00:10:75:1a:89:36
[ 15.679139] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 15.685783] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 15.691108] orion-ehci orion-ehci.0: new USB bus registered, assigned bus num
ber 1
[ 15.721451] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 15.741444] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 15.747991] hub 1-0:1.0: USB hub found
[ 15.751796] hub 1-0:1.0: 1 port detected
[ 15.756249] Initializing USB Mass Storage driver...
[ 15.761234] usbcore: registered new interface driver usb-storage
[ 15.767294] USB Mass Storage support registered.
[ 15.772029] usbcore: registered new interface driver libusual
[ 15.778110] mousedev: PS/2 mouse device common for all mice
[ 16.071449] usb 1-1: new high speed USB device number 2 using orion-ehci
[ 16.223494] hub 1-1:1.0: USB hub found
[ 16.227621] hub 1-1:1.0: 4 ports detected
[ 16.511754] usb 1-1.2: new high speed USB device number 3 using orion-ehci
[ 16.628446] scsi0 : usb-storage 1-1.2:1.0
[ 16.791437] rtc-mv rtc-mv: internal RTC not ticking
[ 16.796503] sdhci: Secure Digital Host Controller Interface driver
[ 16.802739] sdhci: Copyright(c) Pierre Ossman
[ 16.807183] sdhci-pltfm: SDHCI platform and OF driver helper
[ 16.813339] usbcore: registered new interface driver r8712u
[ 16.819810] GRE over IPv4 demultiplexor driver
[ 16.824337] TCP cubic registered
[ 16.827761] NET: Registered protocol family 17
[ 16.832320] lib80211: common routines for IEEE802.11 drivers
[ 16.838015] Registering the dns_resolver key type
[ 16.843356] registered taskstats version 1
[ 16.848128] netconsole: local port 6666
[ 16.852019] netconsole: local IP 172.20.0.127
[ 16.856395] netconsole: interface 'eth0'
[ 16.860336] netconsole: remote port 6666
[ 16.864295] netconsole: remote IP 172.20.0.159
[ 16.868761] netconsole: remote ethernet address ac:16:2d:04:cf:38
[ 16.874899] netconsole: device eth0 not up yet, forcing it
[ 17.632593] scsi 0:0:0:0: Direct-Access USB 2.0 USB Flash Drive 0.00 PQ
: 0 ANSI: 2
[ 18.550553] console [netcon0] enabled
[ 18.554430] netconsole: network logging started
[ 18.559077] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 18.565703] Waiting 10sec before mounting root device...
[ 28.572912] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsyste
m
[ 28.588175] EXT4-fs (sda1): warning: mounting unchecked fs, running e2fsck is
recommended
[ 28.612901] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
[ 28.620039] VFS: Mounted root (ext2 filesystem) on device 8:1.
[ 28.628822] devtmpfs: mounted
[ 28.632506] Freeing init memory: 172K
[ 29.081607] systemd[1]: systemd 204 running in system mode. (+PAM -LIBWRAP -A
UDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 29.297649] systemd[1]: Inserted module 'autofs4'
[ 29.347823] NET: Registered protocol family 10
[ 29.356140] systemd[1]: Inserted module 'ipv6'
[ 29.362062] systemd[1]: Set hostname to <alarm>.
[ 29.546261] systemd[1]: Cannot add dependency job for unit display-manager.se
rvice, ignoring: Unit display-manager.service failed to load: No such file or di
rectory. See system logs and 'systemctl status display-manager.service' for deta
ils.
[ 29.568768] systemd[1]: Expecting device dev-ttyS0.device...
[ 29.591564] systemd[1]: Starting Forward Password Requests to Wall Directory
Watch.
[ 29.599614] systemd[1]: Started Forward Password Requests to Wall Directory W
atch.
[ 29.607378] systemd[1]: Starting Remote File Systems.
[ 29.631580] systemd[1]: Reached target Remote File Systems.
[ 29.637280] systemd[1]: Starting Syslog Socket.
[ 29.661533] systemd[1]: Listening on Syslog Socket.
[ 29.666545] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 29.691524] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 29.698624] systemd[1]: Starting Delayed Shutdown Socket.
[ 29.721525] systemd[1]: Listening on Delayed Shutdown Socket.
[ 29.727401] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ 29.751523] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 29.758203] systemd[1]: Starting LVM2 metadata daemon socket.
[ 29.781526] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 29.787753] systemd[1]: Starting Encrypted Volumes.
[ 29.811519] systemd[1]: Reached target Encrypted Volumes.
[ 29.817071] systemd[1]: Starting Dispatch Password Requests to Console Direct
ory Watch.
[ 29.825403] systemd[1]: Started Dispatch Password Requests to Console Directo
ry Watch.
[ 29.833547] systemd[1]: Starting Paths.
[ 29.851536] systemd[1]: Reached target Paths.
[ 29.856155] systemd[1]: Starting Arbitrary Executable File Formats File Syste
m Automount Point.
[ 29.891538] systemd[1]: Set up automount Arbitrary Executable File Formats Fi
le System Automount Point.
[ 29.901101] systemd[1]: Starting Journal Socket.
[ 29.921528] systemd[1]: Listening on Journal Socket.
[ 29.926694] systemd[1]: Mounted Huge Pages File System.
[ 29.934969] systemd[1]: Started Load Kernel Modules.
[ 29.940104] systemd[1]: Mounted Configuration File System.
[ 29.947610] systemd[1]: Starting Apply Kernel Variables...
[ 30.012748] systemd[1]: Mounted FUSE Control File System.
[ 30.019509] systemd[1]: Starting Create static device nodes in /dev...
[ 30.092088] systemd[1]: Starting Setup Virtual Console...
[ 30.162096] systemd[1]: Starting Journal Service...
[ 30.231713] systemd[1]: Started Journal Service.
[ 30.419624] systemd[1]: Started Set Up Additional Binary Formats.
[ 30.425985] systemd[1]: Mounting POSIX Message Queue File System...
[ 30.491978] systemd[1]: Mounting Debug File System...
[ 30.562256] systemd[1]: Starting udev Kernel Socket.
[ 30.591652] systemd[1]: Listening on udev Kernel Socket.
[ 30.597436] systemd[1]: Starting udev Control Socket.
[ 30.631595] systemd[1]: Listening on udev Control Socket.
[ 30.637479] systemd[1]: Starting udev Coldplug all Devices...
[ 30.702193] systemd[1]: Starting Swap.
[ 30.721641] systemd[1]: Reached target Swap.
[ 30.726090] systemd[1]: Mounting Temporary Directory...
[ 30.801846] systemd[1]: Started File System Check on Root Device.
[ 30.808116] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 30.951546] systemd[1]: Started Apply Kernel Variables.
[ 31.011546] systemd[1]: Started Create static device nodes in /dev.
[ 31.071544] systemd[1]: Started Setup Virtual Console.
[ 31.101541] systemd[1]: Mounted POSIX Message Queue File System.
[ 31.121586] systemd[1]: Mounted Debug File System.
[ 31.191715] systemd[1]: Mounted Temporary Directory.
[ 31.251547] systemd[1]: Started Remount Root and Kernel File Systems.
[ 31.311544] systemd[1]: Started udev Coldplug all Devices.
[ 31.317293] systemd[1]: Starting Load Random Seed...
[ 31.383907] systemd[1]: Starting udev Kernel Device Manager...
[ 31.470438] systemd-udevd[71]: starting version 204
[ 31.511635] systemd[1]: Started Load Random Seed.
[ 31.541659] systemd[1]: Started udev Kernel Device Manager.
[ 31.547512] systemd[1]: Starting Local File Systems (Pre).
[ 31.581618] systemd[1]: Reached target Local File Systems (Pre).
[ 31.587819] systemd[1]: Starting Local File Systems.
[ 31.621649] systemd[1]: Reached target Local File Systems.
[ 31.627496] systemd[1]: Starting Recreate Volatile Files and Directories...
[ 31.722285] systemd[1]: Starting Trigger Flushing of Journal to Persistent St
orage...
[ 31.821618] systemd[1]: Found device /dev/ttyS0.
[ 31.921678] systemd[1]: Started Recreate Volatile Files and Directories.
[ 31.934042] systemd[1]: Starting Update UTMP about System Reboot/Shutdown...
[ 32.481555] systemd[1]: Started Update UTMP about System Reboot/Shutdown.
[ 32.541625] systemd[1]: Started Trigger Flushing of Journal to Persistent Sto
rage.
[ 32.549508] systemd[1]: Starting System Initialization.
[ 32.571533] systemd[1]: Reached target System Initialization.
[ 32.577417] systemd[1]: Starting Daily Cleanup of Temporary Directories.
[ 32.584317] systemd[1]: Started Daily Cleanup of Temporary Directories.
[ 32.591056] systemd[1]: Starting Timers.
[ 32.611629] systemd[1]: Reached target Timers.
[ 32.616232] systemd[1]: Starting D-Bus System Message Bus Socket.
[ 32.641688] systemd[1]: Listening on D-Bus System Message Bus Socket.
[ 32.648321] systemd[1]: Starting Sockets.
[ 32.671602] systemd[1]: Reached target Sockets.
[ 32.676327] systemd[1]: Starting Basic System.
[ 32.701562] systemd[1]: Reached target Basic System.
[ 32.706936] systemd[1]: Starting System Logger Daemon...
[ 32.791649] systemd[1]: Started System Logger Daemon.
[ 32.797281] systemd[1]: Starting Periodic Command Scheduler...
[ 32.881649] systemd[1]: Started Periodic Command Scheduler.
[ 32.887840] systemd[1]: Starting Netcfg multi-profile daemon...
[ 33.671031] systemd[1]: Started SSH Key Generation.
[ 33.681899] systemd[1]: Starting OpenSSH Daemon...
[ 33.771647] systemd[1]: Started OpenSSH Daemon.
[ 33.779590] systemd[1]: Starting Permit User Sessions...
[ 33.852128] systemd[1]: Starting Login Service...
[ 33.922149] systemd[1]: Starting D-Bus System Message Bus...
[ 34.021720] systemd[1]: Started D-Bus System Message Bus.
[ 34.271623] systemd[1]: Started Permit User Sessions.
[ 34.276980] systemd[1]: Starting Getty on tty1...
[ 34.371632] systemd[1]: Started Getty on tty1.
[ 34.379434] systemd[1]: Starting Serial Getty on ttyS0...
[ 34.491681] systemd[1]: Started Serial Getty on ttyS0.
[ 34.497116] systemd[1]: Starting Login Prompts.
[ 34.531640] systemd[1]: Reached target Login Prompts.
[ 34.571652] systemd[1]: Started Login Service.
')

[hydro]

You could mount the drive on another linux installation or live system and investigate /var/log/messages.log . Maybe netcfg fails, it is not clear from netconsole output whether it is started at all. I just installed the current image (2013.06) on a second usb flash drive and kernel netconsole doesn't even report about OpenSSH
$this->bbcode_second_pass_code('', '
[ 25.736860] systemd[1]: Started Remount Root and Kernel File Systems.
[ 25.743592] systemd[1]: Starting Load Random Seed...
[ 25.826949] systemd[1]: Started udev Kernel Device Manager.
[ 25.832820] systemd[1]: Starting Local File Systems (Pre).
[ 25.866858] systemd[1]: Reached target Local File Systems (Pre).
[ 25.926937] systemd[1]: Started Load Random Seed.
')
I can only find it in the journal or logfile after logging in via SSH.
$this->bbcode_second_pass_code('', '

[root@alarm ~]# grep Started /var/log/messages.log | tail
Dec 31 18:00:24 alarm [ 23.856900] systemd[1]: Started udev Coldplug all Devices.
Dec 31 18:00:24 alarm [ 23.986839] systemd[1]: Started Setup Virtual Console.
Dec 31 18:00:24 alarm [ 25.736860] systemd[1]: Started Remount Root and Kernel File Systems.
Dec 31 18:00:24 alarm [ 25.826949] systemd[1]: Started udev Kernel Device Manager.
Dec 31 18:00:24 alarm [ 25.926937] systemd[1]: Started Load Random Seed.
Dec 31 18:00:31 alarm systemd[1]: Started Netcfg multi-profile daemon.
Jun 20 05:06:28 alarm systemd[1]: Started OpenNTP Daemon.
Jun 20 05:06:38 alarm systemd[1]: Started SSH Key Generation.
Jun 20 05:06:38 alarm systemd[1]: Started OpenSSH Daemon.
Jun 20 05:20:58 alarm systemd[1]: Started Cleanup of Temporary Directories.
')

[crousti]

I didnt think of checking this .

So i checked, and found it was my entire fault. I assumed that because i had the netconsole working with dockstar IP set to 172.20.0.127, which is the IP it got assigned from the DHCP when booting on its own system, i would also have that IP when booting archlinux.

It turns out i was wrong ... Archlinux tries to register an IPV6 address, fails, and then got assigned 172.20.0.230, which i did not see on nmap.


Now, for personal information, why would i get 2 different addresses on the same hardware, same mac address, same network ? I thought it would get the same, even if the lease time is not over, it still is the same hardware. Any idea ?

[vivkkrishnan2005]

I have a similar issue - any help? I used debian squeeze on the same drive.

[WarheadsSE]

Because you set one, and asked for the other.

[crousti]

no, i was on DHCP on both.

[davidnewton]

$this->bbcode_second_pass_quote('crousti', '
')
It kind of hangs on Starting kernel.