[SOLVED] ODROID-C1 unable to boot after first shutdown

[EmbeddedGuy]

I have just installed Arch Linux Arm on a 8GB MicroSD, which went quite fine. It booted once and the second time it went wrong. I tried to reinstall Arch on the MicroSD once again and the behaviour repeated.

$this->bbcode_second_pass_code('', '
QA5:A;SVN:B72;POC:17F;STS:0;BOOT:0;INIT:10;BOOT:1;INIT:0;READ:0;CHECK:0;PASS:1;
-----------------------------------------------------------------------
* Welcome to Hardkernel's ODROID-C... (Built at 19:33:00 Dec 8 2014) *
-----------------------------------------------------------------------
CPU : AMLogic S805
MEM : 1024MB (DDR3@792MHz)
BID : HKC13C0001
S/N : HKC1CB0349B68940
0x0000009f
check SD_boot_type:0x1 card_type:0x1
Loading U-boot...success.


U-boot(odroidc@) (Jan 12 2015 - 20:07:16)

DRAM: 1 GiB
relocation Offset is: 2ff1c000
MMC: SDCARD: 0, eMMC: 1
IR init is done!
vpu clk_level = 3
set vpu clk: 182150000Hz, readback: 182150000Hz(0x701)
mode = 6 vic = 4
set HDMI vic: 4
mode is: 6
viu chan = 1
config HPLL
config HPLL done
reconfig packet setting done
MMC read: dev # 0, block # 33984, count 12288 ... 12288 blocks read: OK
There is no valid bmp file at the given address
============================================================
Vendor: Man 824a54 Snr c50a4431 Rev: 0.2 Prod: NCard
Type: Removable Hard Disk
Capacity: 7695.0 MB = 7.5 GB (15759360 x 512)
------------------------------------------------------------
Partition Start Sector Num Sectors Type
1 2048 14680064 83
2 14682112 841728 b
============================================================
Net: Meson_Ethernet
init suspend firmware done. (ret:0)
Hit Enter key to stop autoboot -- : 1  0
exit abortboot: 0

** Unable to use mmc 0:1 for fatload **
Loading file "/boot/boot.ini" from mmc device 0:1 xxa1
1811 bytes read
Loading boot.ini from mmc0:1 (ext4)
Executing the script...
setenv m "1080p" # 1080P 1920x1080
setenv vout_mode "hdmi"
setenv m_bpp "32"
setenv vpu "1"
setenv hdmioutput "1"
setenv bootargs "console=ttyS0,115200n8 root=/dev/mmcblk0p1 rootwait rw no_console_suspend vdaccfg=0xa000 logo=osd1,loaded,0x7900000,720p,full dmfc=3 cvbsmode=576cvbs hdmimode=${m} m_bpp=${m_bpp} vout=${vout_mode} ${disableuhs}"
ext4load mmc 0:1 0x21000000 /boot/uImage
Loading file "/boot/uImage" from mmc device 0:1 xxa1
3829739 bytes read
ext4load mmc 0:1 0x21800000 /boot/dtbs/meson8b_odroidc.dtb
Loading file "/boot/dtbs/meson8b_odroidc.dtb" from mmc device 0:1 xxa1
17785 bytes read
fdt addr 21800000
if test "${vpu}" = "0"; then fdt rm /mesonstream; fdt rm /vdec; fdt rm /ppmgr; fi
if test "${hdmioutput}" = "0"; then fdt rm /mesonfb; fi
bootm 0x21000000 - 0x21800000
## Booting kernel from Legacy Image at 21000000 ...
Image Name: Linux-3.10.44-2-ARCH
Image Type: ARM Linux Kernel Image (lzma compressed)
Data Size: 3829675 Bytes = 3.7 MiB
Load Address: 00208000
Entry Point: 00208000
Verifying Checksum ... OK
## Flattened Device Tree blob at 21800000
Booting using the fdt blob at 0x21800000
Uncompressing Kernel Image ... OK
uboot time: 6342417 us.
Using machid 0xf81 from environment
From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x5008001
Loading Device Tree to 05000000, end 05007578 ... OK

Starting kernel ...

[ 0.000000@0] Booting Linux on physical CPU 0x200
[ 0.000000@0] Initializing cgroup subsys cpuset
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.10.44-2-ARCH (builduser@leming) (gcc version 4.9.2 20141224 (prerelease) (GCC) ) #1 SMP PREEMPT Mon Jan 12 20:20:18 MST 2015
[ 0.000000@0] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c5387d
[ 0.000000@0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000@0] Machine: ODROIDC, model: AMLOGIC
[ 0.000000@0] physical memory start address is 0x200000
[ 0.000000@0] reserved_end is d9fffff
[ 0.000000@0]
[ 0.000000@0] Total memory is 1022 MiB
[ 0.000000@0] Reserved low memory from 0x06000000 to 0x0d9fffff, size: 122 MiB
[ 0.000000@0] mesonfb0(low) : 0x06100000 - 0x07900000 ( 24 MiB)
[ 0.000000@0] mesonfb1(low) : 0x07900000 - 0x07a00000 ( 1 MiB)
[ 0.000000@0] mesonstream0(low) : 0x07a00000 - 0x09a00000 ( 32 MiB)
[ 0.000000@0] vdec0(low) : 0x09a00000 - 0x0da00000 ( 64 MiB)
[ 0.000000@0] ppmgr0(high) : 0x3f000000 - 0x40000000 ( 16 MiB)
[ 0.000000@0] cma: CMA: reserved 8 MiB at 3e800000
[ 0.000000@0] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000@0] Meson chip version = RevA (1B:A - 0:B72)
[ 0.000000@0] PERCPU: Embedded 8 pages/cpu @c150c000 s9344 r8192 d15232 u32768
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 221200
[ 0.000000@0] Kernel command line: console=ttyS0,115200n8 root=/dev/mmcblk0p1 rootwait rw no_console_suspend vdaccfg=0xa000 logo=osd1,loaded,0x7900000,720p,full dmfc=3 cvbsmode=576cvbs hdmimode=1080p m_bpp=32 vout=hdmi
[ 0.000000@0] cvbs trimming line = 0xa000
[ 0.000000@0] cvbs trimming.1.v5: 0xa0, 0x0
[ 0.000000@0] osd1:1
[ 0.000000@0] loaded:268435459
[ 0.000000@0] logo has been loaded
[ 0.000000@0] 720p:10
[ 0.000000@0] full:2
[ 0.000000@0] kernel get cvbsmode form uboot is 576cvbs
[ 0.000000@0] kernel get hdmimode form uboot is 1080p
[ 0.000000@0] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000@0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000@0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000@0] allocated 2060288 bytes of page_cgroup
[ 0.000000@0] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000@0] Memory: 64MB 16MB 790MB = 870MB total
[ 0.000000@0] Memory: 858148k/858148k available, 32732k reserved, 243712K highmem
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000@0] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000@0] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000@0] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000@0] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000@0] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000@0] .text : 0xc0008000 - 0xc0969770 (9606 kB)
[ 0.000000@0] .init : 0xc096a000 - 0xc09a0480 ( 218 kB)
[ 0.000000@0] .data : 0xc09a2000 - 0xc0a1f060 ( 501 kB)
[ 0.000000@0] .bss : 0xc0a1f060 - 0xc0d1f024 (3072 kB)
[ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] NR_IRQS:256
[ 0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
[ 0.000000@0] Global timer: MESON TIMER-F (c09bd640) initialized
[ 0.000000@0] Switching to timer-based delay loop
[ 0.000000@0] Console: colour dummy device 80x30
[ 0.000000@0] console [ttyS0] enabled
[ 0.330728@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
[ 0.341016@0] pid_max: default: 32768 minimum: 301
[ 0.345942@0] Security Framework initialized
[ 0.349998@0] Smack: Initializing.
[ 0.353574@0] Mount-cache hash table entries: 512
[ 0.362339@0] Initializing cgroup subsys memory
[ 0.362666@0] Initializing cgroup subsys devices
[ 0.367215@0] Initializing cgroup subsys freezer
[ 0.371862@0] Initializing cgroup subsys blkio
[ 0.376351@0] CPU: Testing write buffer coherency: ok
[ 0.381715@0] CPU0: thread -1, cpu 0, socket 2, mpidr 80000200
[ 0.387117@0] Setting up static identity map for 0xc06a6530 - 0xc06a6588
[ 0.393873@0] L310 cache controller enabled
[ 0.397864@0] l2x0: 8 ways, 2048 sets, CACHE_ID 0x4100a0c9, Cache size: 524288 B
[ 0.405358@0] AUX_CTRL 0x7ec60001, PERFETCH_CTRL 0x75000007, POWER_CTRL 0x00000000
[ 0.413459@0] TAG_LATENCY 0x00000111, DATA_LATENCY 0x00000222
[ 0.490321@1] CPU1: Booted secondary processor
[ 0.490340@1] CPU1: thread -1, cpu 1, socket 2, mpidr 80000201
[ 0.510313@2] CPU2: Booted secondary processor
[ 0.510331@2] CPU2: thread -1, cpu 2, socket 2, mpidr 80000202
[ 0.530310@3] CPU3: Booted secondary processor
[ 0.530329@3] CPU3: thread -1, cpu 3, socket 2, mpidr 80000203
[ 0.530421@0] Brought up 4 CPUs
[ 0.558601@0] SMP: Total of 4 processors activated (8.00 BogoMIPS).
[ 0.564827@0] CPU: All CPU(s) started in SVC mode.
[ 0.570340@0] devtmpfs: initialized
[ 0.579428@0] clkrate [ xtal ] : 24000000
[ 0.579460@0] clkrate [ pll_sys ] : 1200000000
[ 0.582419@0] clkrate [ pll_fixed ] : 2550000000
[ 0.587070@0] clkrate [ pll_vid ] : 732000000
[ 0.591497@0] clkrate [ pll_ddr ] : 0
[ 0.595209@0] clkrate [ a9_clk ] : 1200000000
[ 0.599625@0] clkrate [ clk81 ] : 159375000
[ 0.604324@0] pinctrl core: initialized pinctrl subsystem
[ 0.609486@0] regulator-dummy: no parameters
[ 0.614032@0] NET: Registered protocol family 16
[ 0.622225@0] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[ 0.626158@0] VPU driver version: v02
[ 0.628806@0] load vpu_clk in dts: 182150000Hz(3)
[ 0.633533@0] vpu_probe OK
[ 0.638521@0] amlogic_gpio gpio: Probed amlogic GPIO driver
[ 0.642044@0] register lm device lm-root
[ 0.645652@0] register lm device lm1
[ 0.649193@0] register lm device lm0
[ 0.652790@0] hw-breakpoint: found 2 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.660857@0] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.666913@0] Init pinux probe!
[ 0.670625@0] pinmux-m8b pinmux: Probed amlogic pinctrl driver
[ 0.675762@0] tv_init_module
[ 0.678598@0] major number 254 for disp
[ 0.682420@0] vout_register_server
[ 0.685779@0] register tv module server ok
[ 0.724114@0] bio: create slab <bio-0> at 0
[ 0.724829@0] SCSI subsystem initialized
[ 0.726743@0] usbcore: registered new interface driver usbfs
[ 0.732275@0] usbcore: registered new interface driver hub
[ 0.737737@0] usbcore: registered new device driver usb
[ 0.742934@0] media: Linux media interface: v0.10
[ 0.747548@0] Linux video capture interface: v2.00
[ 0.752590@0] request vpu clk holdings: venci 106250000Hz
[ 0.757645@0] TV mode 576cvbs selected.
[ 0.761476@0] tvoutc_setmode[458]
[ 0.764746@0] mode is: 7
[ 0.767256@0] VPU_VIU_VENC_MUX_CTRL: 0x5
[ 0.771164@0] viu chan = 1
[ 0.773836@0] VPU_VIU_VENC_MUX_CTRL: 0x5
[ 0.777732@0] config HPLL
[ 0.780342@0] config HPLL done
[ 1.790047@0] vdac open.1 = 0x1, 0x0
[ 1.790075@0] aml_logo: outputmode changed(10->7), reset osd1 scaler.
[ 1.873460@0] Advanced Linux Sound Architecture Driver Initialized.
[ 1.874780@0] cfg80211: Calling CRDA to update world regulatory domain
[ 1.881219@0] NetLabel: Initializing
[ 1.884130@0] NetLabel: domain hash size = 128
[ 1.888632@0] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.893814@0] NetLabel: unlabeled traffic allowed by default
[ 1.900061@0] Switching to clocksource Timer-E
[ 1.913278@0] NET: Registered protocol family 2
[ 1.913810@0] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.919486@0] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.926059@0] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.932498@0] TCP: reno registered
[ 1.935844@0] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 1.941899@0] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 1.948650@0] NET: Registered protocol family 1
[ 1.953190@0] RPC: Registered named UNIX socket transport module.
[ 1.958959@0] RPC: Registered udp transport module.
[ 1.963779@0] RPC: Registered tcp transport module.
[ 1.968646@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.975938@0] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 3 counters available
[ 1.984976@0] bounce pool size: 64 pages
[ 1.992527@0] VFS: Disk quotas dquot_6.5.2
[ 1.992771@0] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.000117@0] NFS: Registering the id_resolver key type
[ 2.003309@0] Key type id_resolver registered
[ 2.007630@0] Key type id_legacy registered
[ 2.011968@0] fuse init (API version 7.22)
[ 2.016542@0] msgmni has been set to 1200
[ 2.021941@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 2.027471@0] io scheduler noop registered
[ 2.031417@0] io scheduler deadline registered
[ 2.035992@0] io scheduler cfq registered (default)
[ 2.097969@0] [drm] Initialized drm 1.1.0 20060810
[ 2.098172@0] gpu cooling register okay with err=0
[ 2.104582@0] Mali: Mali device driver loaded
[ 2.106443@0] UMP: UMP device driver 0000 loaded
[ 2.117598@0] brd: module loaded
[ 2.121085@0] loop: module loaded
[ 2.121812@0] usbcore: registered new interface driver cdc_acm
[ 2.124596@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.132782@0] usbcore: registered new interface driver usb-storage
[ 2.138924@0] usbcore: registered new interface driver ums-alauda
[ 2.144967@0] usbcore: registered new interface driver ums-cypress
[ 2.151100@0] usbcore: registered new interface driver ums-datafab
[ 2.157259@0] usbcore: registered new interface driver ums_eneub6250
[ 2.163560@0] usbcore: registered new interface driver ums-freecom
[ 2.169726@0] usbcore: registered new interface driver ums-isd200
[ 2.175797@0] usbcore: registered new interface driver ums-jumpshot
[ 2.182003@0] usbcore: registered new interface driver ums-karma
[ 2.188000@0] usbcore: registered new interface driver ums-onetouch
[ 2.194260@0] usbcore: registered new interface driver ums-realtek
[ 2.200363@0] usbcore: registered new interface driver ums-sddr09
[ 2.206444@0] usbcore: registered new interface driver ums-sddr55
[ 2.212492@0] usbcore: registered new interface driver ums-usbat
[ 2.218542@0] usbcore: registered new interface driver usbserial
[ 2.224458@0] usbcore: registered new interface driver usbserial_generic
[ 2.231112@0] usbserial: USB Serial support registered for generic
[ 2.237574@0] mousedev: PS/2 mouse device common for all mice
[ 2.243190@0] i2c /dev entries driver
[ 2.247225@0] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.252791@0] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.258558@0] usbcore: registered new interface driver usbhid
[ 2.263997@0] usbhid: USB HID core driver
[ 2.268412@0] zram: Created 1 device(s) ...
[ 2.272380@0] efuse===========================================
[ 2.278105@0] efuse: device efuse created
[ 2.281945@0] efuse--------------------------------------------
[ 2.287807@0] vout_init_module
[ 2.290862@0] start init vout module

[ 2.294599@0] create vout attribute ok

[ 2.298588@0] ge2d_init
[ 2.300954@0] ge2d_dev major:244

[ 2.304442@0] ge2d start monitor

[ 2.307615@0] osd_init
[ 2.307628@1] ge2d workqueue monitor start

[ 2.314101@0] osd_probe, vinfo:c06eba78
[ 2.318153@0] Frame buffer memory assigned at phy:0x06100000, vir:0xf1000000, size=24576K
[ 2.326000@0] osd_probe, mydef_var:c09f29b0, vinfo:c06eba78
[ 2.331524@0] init fbdev bpp is :32

[ 2.335081@0] ---------------clear framebuffer0 memory

[ 2.379038@0] Console: switching to colour frame buffer device 240x67
[ 2.407213@0] Frame buffer memory assigned at phy:0x07900000, vir:0xf0600000, size=1024K
[ 2.415169@0] osd_probe, mydef_var:c09f29b0, vinfo:c06eba78
[ 2.420681@0] don't find to display_size_default from mesonfb-dts
[ 2.426758@0] init fbdev bpp is :24

[ 2.450136@0] osd probe ok

[ 2.510654@0] amlvideo-000: V4L2 device registered as video10
[ 2.511017@0] ionvideo-000: V4L2 device registered as video13
[ 2.516501@0] Video Technology Magazine Ion Video Capture Board ver 1.0 successfully loaded.
[ 2.524980@0] aml_wdt_driver_init,301
[ 2.528510@0] ** disable watchdog
[ 2.532212@0] set uart_ao pinmux use pinctrl subsystem
[ 2.536934@0] P_AO_RTI_PIN_MUX_REG:1801
[ 2.540737@0] start uart_ao_ttyS0:(irq = 122)
[ 2.545101@0] register uart_ao ok
[ 2.548597@0] start uart_a_ttyS1:(irq = 58)
[ 2.552505@0] register uart_a ok
[ 2.555983@0] set uart_b pinmux use pinctrl subsystem
[ 2.560721@0] P_AO_RTI_PIN_MUX_REG:1801
[ 2.564574@0] start uart_b_ttyS2:(irq = 107)
[ 2.568774@0] register uart_b ok
[ 2.572251@0] start uart_d_ttyS4:(irq = 126)
[ 2.576241@0] register uart_d ok
[ 2.579496@0] dwc_otg: version 3.10a 12-MAY-2014
[ 2.584070@0] dwc_otg_driver_probe NOT match
[ 2.628280@0] usb1: type: 1, speed: 0, config: 0, dma: 0, id: 1, phy: fe108820, ctrl: fe080000
[ 2.631260@0] USB (1) use clock source: XTAL input
[ 2.657216@0] Core Release: 3.10a
[ 2.657245@0] Setting default values for core params
[ 2.659841@0] curmode: 1, host_only: 1
[ 2.683744@0] Using Buffer DMA mode
[ 2.683772@0] OTG VER PARAM: 1, OTG VER FLAG: 1
[ 2.686117@0] Working on port type = HOST
[ 2.690331@0] dwc_otg lm1: DWC OTG Controller
[ 2.694460@0] dwc_otg lm1: new USB bus registered, assigned bus number 1
[ 2.701106@0] dwc_otg lm1: irq 63, io mem 0x00000000
[ 2.706035@0] -------hcd->flags.d32 = 0
[ 2.709845@0] Init: Port Power? op_state=1
[ 2.713920@0] Init1: Power Port (0)
[ 2.717944@0] hub 1-0:1.0: USB hub found
[ 2.721270@0] hub 1-0:1.0: 1 port detected
[ 2.725601@0] usb0: type: 0, speed: 0, config: 0, dma: 0, id: 0, phy: fe108800, ctrl: fe040000
[ 2.733936@0] USB (0) use clock source: XTAL input
[ 2.759763@0] Core Release: 3.10a
[ 2.759791@0] Setting default values for core params
[ 2.762384@0] curmode: 1, host_only: 0
[ 2.826252@0] Using Buffer DMA mode
[ 2.826279@0] OTG VER PARAM: 1, OTG VER FLAG: 1
[ 2.828609@0] Working on port type = OTG
[ 2.832513@0] Current port type: SLAVE
[ 2.836433@0] dwc_otg lm0: DWC OTG Controller
[ 2.840578@0] dwc_otg lm0: new USB bus registered, assigned bus number 2
[ 2.847272@0] dwc_otg lm0: irq 62, io mem 0x00000000
[ 2.852678@0] hub 2-0:1.0: USB hub found
[ 2.856092@0] hub 2-0:1.0: 1 port detected
[ 2.860310@0] Dedicated Tx FIFOs mode
[ 2.864130@0] using timer detect id change, eea9a400
[ 2.868843@0] ethernet_driver probe!
[ 2.872270@0] ethernetinit(dbg[c09f7550]=1)
[ 2.876447@0] ethernet base addr is fe0c0000
[ 2.880684@0] write mac add to:eea60bc8: 00 1e 06 b3 49 b6 |...I.|
[ 2.889653@0] libphy: AMLMAC MII Bus: probed
[ 2.891168@0] eth0: PHY ID 001cc916 at 0 IRQ -1 (0:00) active
[ 2.896862@0] eth0: PHY ID 001cc916 at 1 IRQ -1 (0:01) active
[ 2.902701@0] amvideocap_init_module
[ 2.906250@0] Amlogic A/V streaming port init
[ 2.912076@0] init vdec memsource 161480704->228589567
[ 2.915667@0] [tsync_pcr_init]init success.
[ 2.919830@0] regist mpeg12 codec profile
[ 2.923809@0] regist mpeg4 codec profile
[ 2.927719@0] amvdec_vc1 module init
[ 2.927764@1] Indeed it is in host mode hprt0 = 00021501
[ 2.936575@0] regist vc1 codec profile
[ 2.940221@0] amvdec_h264 module init
[ 2.943992@0] regist h264 codec profile
[ 2.947668@0] amvdec_h265 module init
[ 2.951363@0] regist hevc codec profile
[ 2.955221@0] regist mjpeg codec profile
[ 2.959011@0] amvdec_real module init
[ 2.962688@0] regist real codec profile
[ 2.966477@0] amvdec_avs module init
[ 2.970183@0] regist avc codec profile
[ 2.973731@0] jpegenc module init
[ 2.977244@0] alloc_keep_buffer keep_y_addr ee600000
[ 2.982028@0] alloc_keep_buffer keep_u_addr eec00000
[ 2.986945@0] alloc_keep_buffer keep_v_addr eeb80000
[ 2.991867@0] yaddr=ee600000,u_addr=eec00000,v_addr=eeb80000
[ 2.997820@0] create_ge2d_work_queue video task ok
[ 3.002572@0] SARADC Driver init.
[ 3.005749@0] __saradc_probe__
[ 3.103972@1] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 3.105212@0] Indeed it is in host mode hprt0 = 00001101
[ 3.154034@0] saradc calibration: ref_val = 509
[ 3.154064@0] saradc calibration: ref_nominal = 512
[ 3.157775@0] saradc calibration: coef = 4096
[ 3.162336@0] ir irblaster probe
[ 3.170218@0] Remote Driver
[ 3.170308@0] Remote platform_data g_remote_base=fe600580
[ 3.173473@0] set drvdata completed

[ 3.177045@0] device_create_file completed

[ 3.181703@0] input: aml_keypad as /devices/platform/meson-remote/input/input0
[ 3.188813@0] input_register_device completed

[ 3.193012@0] [0x0] = 0x1dd0190
[ 3.196071@0] [0x4] = 0xf800ca
[ 3.199078@0] [0x8] = 0x82006e
[ 3.202108@0] [0xc] = 0x3c0030
[ 3.205157@0] [0x10] = 0x30fa0013
[ 3.208430@0] [0x18] = 0x6f19000
[ 3.211665@0] [0x1c] = 0x9f40
[ 3.214594@0] [0x20] = 0x0
[ 3.217262@0] [0x24] = 0x0
[ 3.219946@0] [0x28] = 0x0
[ 3.222630@0] set_remote_mode[65]
[ 3.225957@0] remote config major:240

[ 3.229815@0] physical address:0x2ed66000
[ 3.233714@0] ==touch_ts_init==
[ 3.236859@0] ==ft5x0x_ts_init==
[ 3.239975@0] ==goodix_ts_init==
[ 3.243198@0] i2c-core: driver [gslx680_compatible] using legacy suspend method
[ 3.250483@0] i2c-core: driver [gslx680_compatible] using legacy resume method
[ 3.257657@0] !!!ntp_ts: ret = 0.
[ 3.260989@0] VTL ct36x TouchScreen driver, <george.chen@vtl.com.cn>.
[ 3.267440@0] i2c-core: driver [ct36x] using legacy suspend method
[ 3.273576@0] i2c-core: driver [ct36x] using legacy resume method
[ 3.279624@0] VTL ct36x TouchScreen driver End.
[ 3.284123@0] ==gsl_ts_init==
[ 3.287080@0] ret=0
[ 3.289301@0] i2c-core: driver [mir3da] using legacy suspend method
[ 3.295447@2] i2c-core: driver [mir3da] using legacy resume method
[ 3.301553@2] i2c-core: driver [lis3dh_acc] using legacy suspend method
[ 3.308145@2] i2c-core: driver [lis3dh_acc] using legacy resume method
[ 3.314658@2] i2c-core: driver [bma222] using legacy suspend method
[ 3.320821@2] i2c-core: driver [bma222] using legacy resume method
[ 3.326088@0] hub 1-1:1.0: USB hub found
[ 3.326427@0] hub 1-1:1.0: 4 ports detected
[ 3.335093@2] i2c-core: driver [dmard06] using legacy suspend method
[ 3.341342@2] i2c-core: driver [dmard06] using legacy resume method
[ 3.347619@2] lsm303d driver: init
[ 3.350997@2] i2c-core: driver [dmard10] using legacy suspend method
[ 3.357292@2] i2c-core: driver [dmard10] using legacy resume method
[ 3.363534@2] stk8313_init
[ 3.366240@2] ======stk831x init ok======
[ 3.370177@2] stk831x_init
[ 3.372885@2] mxc622x accelerometer driver: init
[ 3.377499@2] i2c-core: driver [mxc622x] using legacy suspend method
[ 3.383771@2] i2c-core: driver [mxc622x] using legacy resume method
[ 3.390021@2] mxc6255xc accelerometer driver: init
[ 3.394809@2] i2c-core: driver [mxc6255xc] using legacy suspend method
[ 3.401262@2] i2c-core: driver [mxc6255xc] using legacy resume method
[ 3.407750@2] cm3217 v.1.0.0.1
[ 3.410722@2] i2c-core: driver [elan_epl6814] using legacy suspend method
[ 3.417471@2] i2c-core: driver [elan_epl6814] using legacy resume method
[ 3.424159@2] i2c-core: driver [LTR501] using legacy suspend method
[ 3.430355@2] i2c-core: driver [LTR501] using legacy resume method
[ 3.436652@2] mmc driver version: 1.07, 2014-06-30: eMMC add hw reset function
[ 3.444672@2] host->base fe108e00
[ 3.447066@2] pdata->caps 78007
[ 3.450098@2] pdata->caps2 0
[ 3.452957@2] get property: port, value:0x00000004
[ 3.459487@2] get property: ocr_avail, value:0x00200080
[ 3.465961@2] get property: f_min, value:0x000493e0
[ 3.472438@2] get property: f_max, value:0x05f5e100
[ 3.478946@2] get property: max_req_size, value:0x00020000
[ 3.485441@2] get property: irq_in, value:0x00000003
[ 3.491922@2] get property: irq_out, value:0x00000005
[ 3.498439@2] get property: gpio_cd, str:CARD_6
[ 3.504405@2] get property: pinname, str:sd
[ 3.510019@2] get property: card_type, value:0x00000005
[ 3.516528@2] get property: gpio_dat3, str:CARD_4
[ 3.522488@2] get property: gpio_volsw, str:GPIOAO_3
[ 3.528672@2] normal card in
[ 3.531630@2] aml_sd_voltage_switch[1304] : Switched to voltage -> 3.30 V
[ 3.593963@0] sd: mmc_rescan_try_freq: trying to init card at 400000 Hz
[ 3.593968@2] reg:2620,clearmask=80008,setmask=10001
[ 3.593976@2] reg:2621,clearmask=ff000000,set pin=49
[ 3.593980@2] reg:2623,clearmask=7000,setmask=7
[ 3.593983@2] reg:2620,clearmask=200020,setmask=1
[ 3.593987@2] reg:2622,clearmask=ff00,set pin=49
[ 3.593990@2] reg:2623,clearmask=700000,setmask=7
[ 3.623840@0] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 3.663261@1] sd: new high speed SDHC card at address 59b4, clock 50000000, 4-bit-bus-width
[ 3.666400@1] mmcblk0: sd:59b4 NCard 7.51 GiB
[ 3.671528@1] [aml_sdhc_print_err] sd: data CRC error, port=4, Cmd18 Arg 00000000, xfer_step=3, status=4, cmd25=0, fifo_empty=0, fifo_full=0, timeout=0, Xfer 4096 Bytes, SEND=0x700d2, iSTA=0x549, STAT=0x3c
Pinmux: REG2=0x000000f0, REG3=0x00000000, REG4=0x00000300, REG5=0x00000000, REG6=0xfc003f4f, REG8=0x00000000
[ 3.693932@3] [aml_sdhc_probe] aml_sdhc_probe() success!
[ 3.704619@1] ***********SDHC_REGS***********
[ 3.708911@1] SDHC_ARGU: 0x00000900
[ 3.712374@1] SDHC_SEND: 0x000700d2
[ 3.715851@1] SDHC_CTRL: 0xe7ffe001
[ 3.719325@1] SDHC_STAT: 0x00000020
[ 3.722771@1] SDHC_CLKC: 0x0002f010
[ 3.726246@1] SDHC_ADDR: 0x3ec80200
[ 3.729692@1] SDHC_PDMA: 0x2c43bcf0
[ 3.733155@1] SDHC_MISC: 0xe0000150
[ 3.736639@1] SDHC_DATA: 0xea9f0060
[ 3.740082@1] SDHC_ICTL: 0x000030e6
[ 3.743546@1] SDHC_ISTA: 0x00004549
[ 3.747024@1] SDHC_SRST: 0x00000000
[ 3.750473@1] SDHC_ESTA: 0x00000000
[ 3.753950@1] SDHC_ENHC: 0x00fe0cff
[ 3.757400@1] SDHC_CLK2: 0x0000100f
[ 3.761034@1] mmcblk0: response CRC error sending r/w cmd command, card status 0xb00
[ 3.761648@0] host->base fe108c20
[ 3.761697@0] pdata->caps 80000507
[ 3.761700@0] pdata->caps2 0
[ 3.761705@0] get property: port, value:0x00000002
[ 3.761708@0] get property: ocr_avail, value:0x00200000
[ 3.761711@0] get property: f_min, value:0x000493e0
[ 3.761714@0] get property: f_max, value:0x02faf080
[ 3.761717@0] get property: f_max_w, value:0x02faf080
[ 3.761720@0] get property: max_req_size, value:0x00020000
[ 3.761729@0] get property: pinname, str:emmc
[ 3.761742@0] get property: card_type, value:0x00000001
[ 3.761750@0] get property: gpio_dat3, str:BOOT_3
[ 3.761755@0] [is_emmc_exist] host->storage_flag=0, POR_BOOT_VALUE=1
[ 3.842034@0] [aml_sdhc_print_err] sd: data CRC error, port=4, Cmd18 Arg 00000000, xfer_step=3, status=4, cmd25=0, fifo_empty=0, fifo_full=0, timeout=0, Xfer 4096 Bytes, SEND=0x700d2, iSTA=0x549, STAT=0x20
Pinmux: REG2=0x000000f0, REG3=0x00000000, REG4=0x00000300, REG5=0x00000000, REG6=0xfc003f4f, REG8=0x00000000
[ 3.870592@1] ***********SDHC_REGS***********
[ 3.873937@0] [aml_sdio_probe] aml_sdio_probe() success!
[ 3.874032@0] [dsp]DSP start addr 0xc5e00000
[ 3.874078@0] [dsp]register dsp to char divece(257)
[ 3.875115@0] aml_rtc rtc.0: rtc core: registered aml_rtc as rtc0
[ 3.890290@0] amlogic rfkill init
[ 3.890651@0] aml_hw_crypto initialization.
[ 3.891888@0] enter rt5616_modinit
[ 3.892006@0] dummy_codec_platform_probe
[ 3.892453@0] i2s get no clk src setting in dts, use the default mpll 0
[ 3.892788@0] test codec dummy_codec
[ 3.892793@0] using external codec, index = 1
[ 3.892795@0] using external dummy codec
[ 3.892900@0] enter spdif_dit_probe
[ 3.892902@0] aml_spdif_unmute
[ 3.893025@0] codec_name = dummy_codec.0
[ 3.939000@1] SDHC_ARGU: 0x00000900
[ 3.939266@0] spk_event delay_time = 130
[ 3.946361@1] SDHC_SEND: 0x000700d2
[ 3.949799@1] SDHC_CTRL: 0xe7ffe001
[ 3.953262@1] SDHC_STAT: 0x00000020
[ 3.956742@1] SDHC_CLKC: 0x0002f010
[ 3.960190@1] SDHC_ADDR: 0x3ec80200
[ 3.963653@1] SDHC_PDMA: 0x2c43bcf0
[ 3.967131@1] SDHC_MISC: 0xe0000150
[ 3.970580@1] SDHC_DATA: 0xea9f0060
[ 3.974059@1] SDHC_ICTL: 0x000030e6
[ 3.977507@1] SDHC_ISTA: 0x00004549
[ 3.980970@1] SDHC_SRST: 0x00000000
[ 3.984448@1] SDHC_ESTA: 0x00000000
[ 3.987898@1] SDHC_ENHC: 0x00fe0cff
[ 3.991361@1] SDHC_CLK2: 0x0000100f
[ 3.995005@1] mmcblk0: response CRC error sending r/w cmd command, card status 0xb00
[ 3.995661@0] aml-i2s 0:playback preallocate_dma_buffer: area=f04fc000, addr=3ed00000, size=524288
[ 4.011755@0] aml-i2s 1:capture preallocate_dma_buffer: area=f057e000, addr=3ec40000, size=65536
[ 4.020271@0] aml_snd_m8 aml_m8_sound_card.4: dummy_codec <-> aml-i2s-dai.0 mapping ok
[ 4.028190@1] [aml_sdhc_print_err] sd: data CRC error, port=4, Cmd18 Arg 00000000, xfer_step=3, status=4, cmd25=0, fifo_empty=0, fifo_full=0, timeout=0, Xfer 4096 Bytes, SEND=0x700d2, iSTA=0x4549, STAT=0x3c
[ 4.028190@1] Pinmux: REG2=0x000000f0, REG3=0x00000000, REG4=0x00000300, REG5=0x00000000, REG6=0xfc003f4f, REG8=0x00000000
[ 4.058669@1] ***********SDHC_REGS***********
[ 4.062970@1] SDHC_ARGU: 0x00000900
[ 4.066445@1] SDHC_SEND: 0x000700d2
[ 4.069897@1] SDHC_CTRL: 0xe7ffe001
[ 4.073360@1] SDHC_STAT: 0x0000003e
[ 4.076844@1] SDHC_CLKC: 0x0002f010
[ 4.080287@1] SDHC_ADDR: 0x3ec80200
[ 4.083751@1] SDHC_PDMA: 0x2c43bcf0
[ 4.087227@1] SDHC_MISC: 0xe0000150
[ 4.090678@1] SDHC_DATA: 0xea9f0060
[ 4.094153@1] SDHC_ICTL: 0x000030e6
[ 4.097605@1] SDHC_ISTA: 0x00004549
[ 4.101068@1] SDHC_SRST: 0x00000000
[ 4.104543@1] SDHC_ESTA: 0x00000000
[ 4.107996@1] SDHC_ENHC: 0x00fe0cff
[ 4.111459@1] SDHC_CLK2: 0x0000100f
[ 4.115124@1] mmcblk0: response CRC error sending r/w cmd command, card status 0xb00
[ 4.115900@0] aml-i2s 0:playback preallocate_dma_buffer: area=f0701000, addr=3ee00000, size=524288
[ 4.131864@0] aml-i2s 1:capture preallocate_dma_buffer: area=f059f000, addr=3ec60000, size=65536
[ 4.140356@0] aml_snd_m8 aml_m8_sound_card.4: dit-hifi <-> aml-spdif-dai.0 mapping ok
[ 4.140375@1] [aml_sdhc_print_err] sd: data CRC error, port=4, Cmd18 Arg 00000000, xfer_step=3, status=4, cmd25=0, fifo_empty=0, fifo_full=0, timeout=0, Xfer 4096 Bytes, SEND=0x700d2, iSTA=0x549, STAT=0x24
[ 4.140375@1] Pinmux: REG2=0x000000f0, REG3=0x00000000, REG4=0x00000300, REG5=0x00000000, REG6=0xfc003f4f, REG8=0x00000000
[ 4.140389@1] ***********SDHC_REGS***********
[ 4.140391@1] SDHC_ARGU: 0x00000900
[ 4.140393@1] SDHC_SEND: 0x000700d2
[ 4.140395@1] SDHC_CTRL: 0xe7ffe001
[ 4.140396@1] SDHC_STAT: 0x00000030
[ 4.140398@1] SDHC_CLKC: 0x0002f010
[ 4.140400@1] SDHC_ADDR: 0x3ec80200
[ 4.140402@1] SDHC_PDMA: 0x2c43bcf0
[ 4.140404@1] SDHC_MISC: 0xe0000150
[ 4.140405@1] SDHC_DATA: 0xeadf0060
[ 4.140407@1] SDHC_ICTL: 0x000030e6
[ 4.140409@1] SDHC_ISTA: 0x00000549
[ 4.140410@1] SDHC_SRST: 0x00000000
[ 4.140412@1] SDHC_ESTA: 0x00000000
[ 4.140414@1] SDHC_ENHC: 0x00fe0cff
[ 4.140416@1] SDHC_CLK2: 0x0000100f
[ 4.234971@1] mmcblk0: response CRC error sending r/w cmd command, card status 0xb00
[ 4.236461@0] -----ext_codec=1---
[ 4.236464@0] aml_snd_m8: faild to get mute_gpio!
[ 4.236467@0] =aml_m8_pinmux_init==,aml_m8_pinmux_init done,---0
[ 4.236599@0] GACT probability NOT on
[ 4.236607@0] Mirror/redirect action on
[ 4.236619@0] u32 classifier
[ 4.236621@0] Actions configured
[ 4.236626@0] Netfilter messages via NETLINK v0.30.
[ 4.236877@0] TCP: cubic registered
[ 4.237403@0] NET: Registered protocol family 10
[ 4.238130@0] mip6: Mobile IPv6
[ 4.238138@0] NET: Registered protocol family 17
[ 4.238162@0] NET: Registered protocol family 15
[ 4.238245@0] Key type dns_resolver registered
[ 4.299983@0] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[ 4.303051@1] [aml_sdhc_print_err] sd: data CRC error, port=4, Cmd18 Arg 00000000, xfer_step=3, status=4, cmd25=0, fifo_empty=0, fifo_full=0, timeout=0, Xfer 4096 Bytes, SEND=0x700d2, iSTA=0x4549, STAT=0x2c
[ 4.303051@1] Pinmux: REG2=0x000000f0, REG3=0x00000000, REG4=0x00000300, REG5=0x00000000, REG6=0xfc003f4f, REG8=0x00000000
[ 4.303065@1] ***********SDHC_REGS***********
[ 4.303067@1] SDHC_ARGU: 0x00000900
[ 4.303069@1] SDHC_SEND: 0x000700d2
[ 4.303070@1] SDHC_CTRL: 0xe7ffe001
[ 4.303072@1] SDHC_STAT: 0x00000032
[ 4.303074@1] SDHC_CLKC: 0x0002f010
[ 4.303076@1] SDHC_ADDR: 0x3ec80200
[ 4.303078@1] SDHC_PDMA: 0x2c43bcf0
[ 4.303080@1] SDHC_MISC: 0xe0000150
[ 4.303081@1] SDHC_DATA: 0xea9f0060
[ 4.303083@1] SDHC_ICTL: 0x000030e6
[ 4.303085@1] SDHC_ISTA: 0x00000549
[ 4.303086@1] SDHC_SRST: 0x00000000
[ 4.303088@1] SDHC_ESTA: 0x00000000
[ 4.303090@1] SDHC_ENHC: 0x00fe0cff
[ 4.303092@1] SDHC_CLK2: 0x0000100f
[ 4.394621@0] Registering SWP/SWPB emulation handler
[ 4.394636@1] mmcblk0: response CRC error sending r/w cmd command, card status 0xb00
[ 4.407190@0] enter meson_pm_init
[ 4.407226@1] [aml_sdhc_print_err] sd: data CRC error, port=4, Cmd18 Arg 00000000, xfer_step=3, status=4, cmd25=0, fifo_empty=0, fifo_full=0, timeout=0, Xfer 4096 Bytes, SEND=0x700d2, iSTA=0x4549, STAT=0x20
[ 4.407226@1] Pinmux: REG2=0x000000f0, REG3=0x00000000, REG4=0x00000300, REG5=0x00000000, REG6=0xfc003f4f, REG8=0x00000000
[ 4.407240@1] ***********SDHC_REGS***********
[ 4.407242@1] SDHC_ARGU: 0x00000900
[ 4.407244@1] SDHC_SEND: 0x000700d2
[ 4.407246@1] SDHC_CTRL: 0xe7ffe001
[ 4.407248@1] SDHC_STAT: 0x00000020
[ 4.407249@1] SDHC_CLKC: 0x0002f010
[ 4.407251@1] SDHC_ADDR: 0x3ec80200
[ 4.407253@1] SDHC_PDMA: 0x2c43bcf0
[ 4.407255@1] SDHC_MISC: 0xe0000150
[ 4.407257@1] SDHC_DATA: 0xea9f0060
[ 4.407259@1] SDHC_ICTL: 0x000030e6
[ 4.407260@1] SDHC_ISTA: 0x00004549
[ 4.407262@1] SDHC_SRST: 0x00000000
[ 4.407264@1] SDHC_ESTA: 0x00000000
[ 4.407265@1] SDHC_ENHC: 0x00fe0cff
[ 4.407267@1] SDHC_CLK2: 0x0000100f
[ 4.497339@1] mmcblk0: response CRC error sending r/w cmd command, card status 0xb00
[ 4.497443@0] enter meson_pm_probe!
[ 4.497449@0] meson_pm_probe done !
[ 4.498015@0] registered taskstats version 1
[ 4.498090@0] regulator-dummy: disabling
[ 4.498376@0] Mali DRM initialize, driver name: mali_drm, version 2.1
[ 4.498704@0] [drm] Initialized mali_drm 2.1.1 20140306 on minor 0
[ 4.498724@0] Mali DRM initialize, driver name: mali_drm, version 2.1
[ 4.498958@0] [drm] Initialized mali_drm 2.1.1 20140306 on minor 1
[ 4.545119@0] console [netcon0] enabled
[ 4.545144@1] end_request: I/O error, dev mmcblk0, sector 0
[ 4.545151@1] Buffer I/O error on device mmcblk0, logical block 0
[ 4.560602@0] netconsole: network logging started
[ 4.565200@0] aml_rtc rtc.0: setting system clock to 1995-03-10 19:43:33 UTC (794864613)
[ 4.565215@1] [aml_sdhc_print_err] sd: data CRC error, port=4, Cmd18 Arg 00000000, xfer_step=3, status=4, cmd25=0, fifo_empty=0, fifo_full=0, timeout=0, Xfer 4096 Bytes, SEND=0x700d2, iSTA=0x4549, STAT=0x20
[ 4.565215@1] Pinmux: REG2=0x000000f0, REG3=0x00000000, REG4=0x00000300, REG5=0x00000000, REG6=0xfc003f4f, REG8=0x00000000
[ 4.565229@1] ***********SDHC_REGS***********
[ 4.565231@1] SDHC_ARGU: 0x00000900
[ 4.565233@1] SDHC_SEND: 0x000700d2
[ 4.565235@1] SDHC_CTRL: 0xe7ffe001
[ 4.565237@1] SDHC_STAT: 0x00000020
[ 4.565239@1] SDHC_CLKC: 0x0002f010
[ 4.565240@1] SDHC_ADDR: 0x3ec80200
[ 4.565242@1] SDHC_PDMA: 0x2c43bcf0
[ 4.565244@1] SDHC_MISC: 0xe0000150
[ 4.565246@1] SDHC_DATA: 0xea9f0060
[ 4.565247@1] SDHC_ICTL: 0x000030e6
[ 4.565249@1] SDHC_ISTA: 0x00004549
[ 4.565251@1] SDHC_SRST: 0x00000000
[ 4.565252@1] SDHC_ESTA: 0x00000000
[ 4.565254@1] SDHC_ENHC: 0x00fe0cff
[ 4.565256@1] SDHC_CLK2: 0x0000100f
[ 4.660116@1] mmcblk0: response CRC error sending r/w cmd command, card status 0xb00
[ 4.660120@0] ### dt-test ### No testcase data in device tree; not running tests
[ 4.660242@0] meson_cpufreq_probe:SYSPLL request to be fixed
[ 4.660245@0] meson_cpufreq: no voltage_control prop
[ 4.660248@0] voltage_control = 0
[ 4.661124@0] <<-GTP-INFO->> GTP driver installing...
[ 4.661366@0] buf[0]=ec,buf[1]=af,err=4
[ 4.661370@0] adc=383,TS_C=12,flag=1
[ 4.661372@0] efuse_flag=a
[ 4.661376@0] amlogic_thermal_probe, this chip is trimmed, use thermal
[ 4.661381@0] amlogic-thermal aml_thermal: amlogic thermal probe start
[ 4.661385@0] #thermal-cells=7
[ 4.661388@0] pdata->temp_trip_count=4
[ 4.661392@0] temperature=70 on trip point=0
[ 4.661398@0] fixing high_freq=1488001 to 1250000 at trip point 0,level=1
[ 4.661403@0] fixing low_freq=1488001 to 1250000 at trip point 0,level=1
[ 4.661406@0] gpu[0].gpu_high_freq=511,tmp_level[0].gpu_high_freq=511
[ 4.661407@0] cpu[0] core num==3
[ 4.661409@0] gpu[0] core num==2
[ 4.661411@0] temperature=80 on trip point=1
[ 4.661415@0] fixing high_freq=1200001 to 768000 at trip point 1,level=2
[ 4.661419@0] fixing low_freq=1200001 to 768000 at trip point 1,level=2
[ 4.661421@0] gpu[1].gpu_high_freq=435,tmp_level[1].gpu_high_freq=435
[ 4.661423@0] cpu[1] core num==2
[ 4.661425@0] gpu[1] core num==2
[ 4.661427@0] temperature=90 on trip point=2
[ 4.661431@0] fixing high_freq=800001 to 768000 at trip point 2,level=2
[ 4.661434@0] fixing low_freq=800001 to 768000 at trip point 2,level=2
[ 4.661437@0] gpu[2].gpu_high_freq=328,tmp_level[2].gpu_high_freq=328
[ 4.661439@0] cpu[2] core num==1
[ 4.661440@0] gpu[2] core num==1
[ 4.661442@0] temperature=110 on trip point=3
[ 4.661446@0] fixing high_freq=-1 to -22 at trip point 3,level=-1
[ 4.661450@0] fixing low_freq=-1 to -22 at trip point 3,level=-1
[ 4.661452@0] gpu[3].gpu_high_freq=-1,tmp_level[3].gpu_high_freq=-1
[ 4.661454@0] cpu[3] core num==-1
[ 4.661456@0] gpu[3] core num==-1
[ 4.661458@0] idle interval=1000
[ 4.661460@0] pdata->name:aml_thermal
[ 4.661735@0] tmp_trip[0].cpu_core_upper=1
[ 4.661747@0] tmp_trip[1].cpu_core_upper=2
[ 4.661755@0] tmp_trip[2].cpu_core_upper=3
[ 4.661764@0] tmp_trip[3].cpu_core_upper=-1
[ 4.661773@0] aml_thermal bind thermal-cpucore-0 okay !
[ 4.661804@0] aml_thermal bind thermal-cpufreq-0 okay !
[ 4.661809@0] pdata->tmp_trip[0].gpu_lower_level=1
[ 4.661811@0] pdata->tmp_trip[0].gpu_upper_level=1
[ 4.661821@0] pdata->tmp_trip[1].gpu_lower_level=2
[ 4.661822@0] pdata->tmp_trip[1].gpu_upper_level=2
[ 4.661831@0] pdata->tmp_trip[2].gpu_lower_level=4
[ 4.661833@0] pdata->tmp_trip[2].gpu_upper_level=4
[ 4.661843@0] pdata->tmp_trip[3].gpu_lower_level=-1
[ 4.661845@0] pdata->tmp_trip[3].gpu_upper_level=-1
[ 4.661861@0] aml_thermal bind thermal-gpufreq-0 okay !
[ 4.661997@0] amlogic: Kernel Thermal management registered
[ 4.662002@0] amlogic-thermal aml_thermal: amlogic thermal probe done
[ 4.662289@0] input: cec_input as /devices/virtual/input/input1
[ 4.6624[ 4.945324@0] [aml_sdhc_print_err] sd: data CRC error, port=4, Cmd18 Arg 00000000, xfer_step=3, status=4, cmd25=0, fifo_empty=0, fifo_full=0, timeout=0, Xfer 4096 Bytes, SEND=0x700d2, iSTA=0x4549, STAT=0x20
Pinmux: REG2=0x000000f0, REG3=0x00000000, REG4=0x00000300, REG5=0x00000000, REG6=0xfc003f4f, REG8=0x00000000
[ 4.968735@1] ***********SDHC_REGS***********
[ 4.973047@1] SDHC_ARGU: 0x00000900
[ 4.976520@1] SDHC_SEND: 0x000700d2
[ 4.979975@1] SDHC_CTRL: 0xe7ffe001
[ 4.983437@1] SDHC_STAT: 0x00000020
[ 4.986910@1] SDHC_CLKC: 0x0002f010
[ 4.990365@1] SDHC_ADDR: 0x3ec80200
[ 4.993828@1] SDHC_PDMA: 0x2c43bcf0
[ 4.997300@1] SDHC_MISC: 0xe0000150
[ 5.000755@1] SDHC_DATA: 0xea9f0060
[ 5.004227@1] SDHC_ICTL: 0x000030e6
[ 5.007682@1] SDHC_ISTA: 0x00004549
[ 5.011146@1] SDHC_SRST: 0x00000000
[ 5.014618@1] SDHC_ESTA: 0x00000000
[ 5.018073@1] SDHC_ENHC: 0x00fe0cff
[ 5.021536@1] SDHC_CLK2: 0x0000100f
[ 5.025109@1] mmcblk0: response CRC error sending r/w cmd command, card status 0xb00
[ 5.033031@1] [aml_sdhc_print_err] sd: data CRC error, port=4, Cmd18 Arg 00000000, xfer_step=3, status=4, cmd25=0, fifo_empty=0, fifo_full=0, timeout=0, Xfer 4096 Bytes, SEND=0x700d2, iSTA=0x4549, STAT=0x22
Pinmux: REG2=0x000000f0, REG3=0x00000000, REG4=0x00000300, REG5=0x00000000, REG6=0xfc003f4f, REG8=0x00000000
....
[ 7.138288@1] mmc_blk_reset 938 reset error md->reset_done:1 and type:1
[ 7.144865@1] end_request: I/O error, dev mmcblk0, sector 0
[ 7.150397@1] Buffer I/O error on device mmcblk0, logical block 0
[ 7.156479@1] mmcblk0: unable to read partition table
[ 7.161782@1] emmc: mmc_rescan_try_freq: trying to init card at 400000 Hz
[ 7.168341@1] aml_emmc_hw_reset 1374
[ 7.193927@0] Changing uart_ao_ttyS0: baud from 0 to 115200
[ 7.214272@0] VFS: Cannot open root device "mmcblk0p1" or unknown-block(179,1): error -6
[ 7.216728@0] Please append a correct "root=" boot option; here are the available partitions:
[ 7.225276@0] b300 7879680 mmcblk0 driver: mmcblk
[ 7.230720@0] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,1)
[ 7.239302@0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.44-2-ARCH #1
[ 7.246094@0] [<c0013f10>] (unwind_backtrace+0x0/0xec) from [<c00118f4>] (show_stack+0x10/0x14)
[ 7.254765@0] [<c00118f4>] (show_stack+0x10/0x14) from [<c069c328>] (panic+0x9c/0x1ec)
[ 7.262668@0] [<c069c328>] (panic+0x9c/0x1ec) from [<c096b038>] (mount_block_root+0x214/0x2a8)
[ 7.271262@0] [<c096b038>] (mount_block_root+0x214/0x2a8) from [<c096b3ac>] (prepare_namespace+0x190/0x1d4)
[ 7.280988@0] [<c096b3ac>] (prepare_namespace+0x190/0x1d4) from [<c096ad08>] (kernel_init_freeable+0x22c/0x23c)
[ 7.291063@0] [<c096ad08>] (kernel_init_freeable+0x22c/0x23c) from [<c0697880>] (kernel_init+0x8/0x160)
[ 7.300441@0] [<c0697880>] (kernel_init+0x8/0x160) from [<c000e118>] (ret_from_fork+0x14/0x3c)
[ 7.309035@1] CPU1: stopping
[ 7.311899@1] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.10.44-2-ARCH #1
[ 7.318680@1] [<c0013f10>] (unwind_backtrace+0x0/0xec) from [<c00118f4>] (show_stack+0x10/0x14)
[ 7.327361@1] [<c00118f4>] (show_stack+0x10/0x14) from [<c0013134>] (handle_IPI+0xd4/0x17c)
[ 7.335696@1] [<c0013134>] (handle_IPI+0xd4/0x17c) from [<c0008470>] (gic_handle_irq+0x58/0x5c)
[ 7.344380@1] [<c0008470>] (gic_handle_irq+0x58/0x5c) from [<c000dc40>] (__irq_svc+0x40/0x70)
[ 7.352885@1] Exception stack(0xef29ffa0 to 0xef29ffe8)
[ 7.358100@1] ffa0: 00000001 00000000 00001084 00000000 ef29e000 c09b6550 c06a9c2c ef29e030
[ 7.366436@1] ffc0: c0a1e87a c0a1e87a ef29e000 00000000 01000000 ef29ffe8 c000ee00 c000ee04
[ 7.374769@1] ffe0: 60000113 ffffffff
[ 7.378422@1] [<c000dc40>] (__irq_svc+0x40/0x70) from [<c000ee04>] (arch_cpu_idle+0x28/0x2c)
[ 7.386846@1] [<c000ee04>] (arch_cpu_idle+0x28/0x2c) from [<c007332c>] (cpu_startup_entry+0xf4/0x150)
[ 7.396049@1] [<c007332c>] (cpu_startup_entry+0xf4/0x150) from [<00898b24>] (0x898b24)
[ 7.403948@3] CPU3: stopping
[ 7.406814@3] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 3.10.44-2-ARCH #1
[ 7.413595@3] [<c0013f10>] (unwind_backtrace+0x0/0xec) from [<c00118f4>] (show_stack+0x10/0x14)
[ 7.422276@3] [<c00118f4>] (show_stack+0x10/0x14) from [<c0013134>] (handle_IPI+0xd4/0x17c)
[ 7.430611@3] [<c0013134>] (handle_IPI+0xd4/0x17c) from [<c0008470>] (gic_handle_irq+0x58/0x5c)
[ 7.439295@3] [<c0008470>] (gic_handle_irq+0x58/0x5c) from [<c000dc40>] (__irq_svc+0x40/0x70)
[ 7.447800@3] Exception stack(0xef2a3fa0 to 0xef2a3fe8)
[ 7.453015@3] 3fa0: 00000003 00000000 00000446 00000000 ef2a2000 c09b6550 c06a9c2c ef2a2030
[ 7.461351@3] 3fc0: c0a1e87a c0a1e87a ef2a2000 00000000 01000000 ef2a3fe8 c000ee00 c000ee04
[ 7.469684@3] 3fe0: 60000113 ffffffff
[ 7.473337@3] [<c000dc40>] (__irq_svc+0x40/0x70) from [<c000ee04>] (arch_cpu_idle+0x28/0x2c)
[ 7.481760@3] [<c000ee04>] (arch_cpu_idle+0x28/0x2c) from [<c007332c>] (cpu_startup_entry+0xf4/0x150)
[ 7.490963@3] [<c007332c>] (cpu_startup_entry+0xf4/0x150) from [<00898b24>] (0x898b24)
[ 7.498863@2] CPU2: stopping
[ 7.501730@2] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 3.10.44-2-ARCH #1
[ 7.508510@2] [<c0013f10>] (unwind_backtrace+0x0/0xec) from [<c00118f4>] (show_stack+0x10/0x14)
[ 7.517191@2] [<c00118f4>] (show_stack+0x10/0x14) from [<c0013134>] (handle_IPI+0xd4/0x17c)
[ 7.525526@2] [<c0013134>] (handle_IPI+0xd4/0x17c) from [<c0008470>] (gic_handle_irq+0x58/0x5c)
[ 7.534210@2] [<c0008470>] (gic_handle_irq+0x58/0x5c) from [<c000dc40>] (__irq_svc+0x40/0x70)
[ 7.542715@2] Exception stack(0xef2a1fa0 to 0xef2a1fe8)
[ 7.547930@2] 1fa0: 00000002 00000000 000005d2 00000000 ef2a0000 c09b6550 c06a9c2c ef2a0030
[ 7.556266@2] 1fc0: c0a1e87a c0a1e87a ef2a0000 00000000 01000000 ef2a1fe8 c000ee00 c000ee04
[ 7.564599@2] 1fe0: 60000113 ffffffff
[ 7.568252@2] [<c000dc40>] (__irq_svc+0x40/0x70) from [<c000ee04>] (arch_cpu_idle+0x28/0x2c)
[ 7.576675@2] [<c000ee04>] (arch_cpu_idle+0x28/0x2c) from [<c007332c>] (cpu_startup_entry+0xf4/0x150)
[ 7.585878@2] [<c007332c>] (cpu_startup_entry+0xf4/0x150) from [<00898b24>] (0x898b24)
')

[EmbeddedGuy]

I disabled UHS and it worked!