GFH 2TB: Kernel not starting

[Nik]

Hello, I was reading several posts about my problem, and tried to use te given information for my problem, but I am not able to get my GFH running again.

I was doing the archlinux install step by step (http://archlinuxarm.org/platforms/armv5 ... oflex-home)
It was working till step 17 (You need to set your MAC address to the what's on the sticker on the bottom of the device)
also step 18 was bringing an error, and the message that I have to reboot, to set MAC address.
I was not doing the next steps and did the reboot, which was displayed. Now I am only able to get into uboot via netcat, but it seems that the kernel is not able to get startet, maybe because I was not doing this command "tune2fs -L "rootfs" /dev/sda1"

1) Is there a possibility to do, the lasts steps from marvell uboot?
2) Which other possibilites may help to make my GFH running again?

Hope someone can help me

thx Nik

$this->bbcode_second_pass_code('', 'U-Boot 2010.09 (Feb 16 2011 - 18:44:23)
UBIT v0.6 by Jeff Doozan and Peter Carmichael
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices...
USB device not accepting new address (error=20)
2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 3
1
va 0
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:fast", error -19
Error reading superblock on volume 'ubi:fast'!
UBIFS not mounted, use ubifs mount to mount volume first!
** Block device usb 0 not supported
** Block device usb 0 not supported

** Invalid boot device **

** Invalid boot device **
** Block device usb 1 not supported
** Block device usb 1 not supported

** Invalid boot device **

** Invalid boot device **
** Block device usb 2 not supported
** Block device usb 2 not supported

** Invalid boot device **

** Invalid boot device **
** Block device usb 3 not supported
** Block device usb 3 not supported

** Invalid boot device **

** Invalid boot device **

Reset IDE: Bus 0: OK Bus 1: not available
Device 0: Model: ST2000DL001-9VT156 Firm: CC96 Ser#: 5YD0C2ZY
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Loading file "/boot/uImage" from ide device 0:1 (hda1)
nö,
2861640 bytes read
Loading file "/uInitrd" from ide device 0:1 (hda1)
** File not found /uInitrd
Loading file "/boot/uInitrd" from ide device 0:1 (hda1)
** File not found /boot/uInitrd
## Booting kernel from Legacy Image at 00680000 ...
Image Name: Linux-3.1.10-9-ARCH
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2861576 Bytes = 2.7 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...
')

[WarheadsSE]

1) Check the output of the kernel's netcat
2) Attach the device to a ext2/3 speaking system, via USB or SATA and use `tune2fs -L "rootfs" /dev/sdZ1` where Z is the appropriate.

[Nik]

THank you, I'll have a try, and response than