Raspberry Pi 2

The Raspberry Pi 2 is the successor to the Raspberry Pi. It builds upon the original model B+ upgrading to 1 GB of RAM, and replacing the aged ARMv6 single-core with an ARMv7 Cortex-A7 quad-core.

The Raspberry Pi 2 measures 85.60mm x 53.98mm x 17mm, with a little overlap for the SD card and connectors which project over the edges. The SoC is a Broadcom BCM2836. This contains an quad-core Cortex-A7 running at 900Mhz, and a Videocore 4 GPU.

ARMv7 Cortex-A7
Broadcom BCM2836 900MHz
Micro SD

Replace sdX in the following instructions with the device name for the SD card as it appears on your computer.

  1. Start fdisk to partition the SD card:
    fdisk /dev/sdX
  2. At the fdisk prompt, delete old partitions and create a new one:
    1. Type o. This will clear out any partitions on the drive.
    2. Type p to list partitions. There should be no partitions left.
    3. Type n, then p for primary, 1 for the first partition on the drive, press ENTER to accept the default first sector, then type +200M for the last sector.
    4. Type t, then c to set the first partition to type W95 FAT32 (LBA).
    5. Type n, then p for primary, 2 for the second partition on the drive, and then press ENTER twice to accept the default first and last sector.
    6. Write the partition table and exit by typing w.
  3. Create and mount the FAT filesystem:
    mkfs.vfat /dev/sdX1
    mkdir boot
    mount /dev/sdX1 boot
  4. Create and mount the ext4 filesystem:
    mkfs.ext4 /dev/sdX2
    mkdir root
    mount /dev/sdX2 root
  5. Download and extract the root filesystem (as root, not via sudo):
    wget http://os.archlinuxarm.org/os/ArchLinuxARM-rpi-armv7-latest.tar.gz
    bsdtar -xpf ArchLinuxARM-rpi-armv7-latest.tar.gz -C root
  6. Move boot files to the first partition:
    mv root/boot/* boot
  7. Unmount the two partitions:
    umount boot root
  8. Insert the SD card into the Raspberry Pi, connect ethernet, and apply 5V power.
  9. Use the serial console or SSH to the IP address given to the board by your router.
    • Login as the default user alarm with the password alarm.
    • The default root password is root.
  10. Initialize the pacman keyring and populate the Arch Linux ARM package signing keys:
    pacman-key --init
    pacman-key --populate archlinuxarm


alsa-utils should supply the needed programs to use onboard sound. Default volume can be adjusted using alsamixer.

A key change with Linux kernel version 4.4.x for ARM related to ALSA and to the needed sound module: in order to use tools such as alsamixer with the current kernel, users must modify /boot/config.txt to contain the following line:


Caveats for Audio

To force audio over HDMI, add this to /boot/config.txt:


If you experience distortion using the 3.5mm analogue output:




To be able to talk to the bluetooth chip, you must install the services, firmware, and UDEV rules. The pi-bluetooth package from the AUR is available to do this.


The BCM43* series chips are notorious for problems when both wifi and bluetooth are used at the same time. This coexistence issue comes in varying degrees of severity but for most users makes using the Pi in bluetooth A2DP mode while also using wifi impossible. Bluetooth buffer underruns are caused by sharing the UART device, resulting in skipping, popping, hissing, and generally unusable audio. For some users, this also effects peripherals such as mice and keyboards. A firmware fix was found for both the Pi3 and Pi ZeroW, discussion of this fix can be found in this github issue.

To deploy the fix to the current firmware in Arch add the following lines:


to the end of these firmware config files:



This fix can be found in this git commit. The fix is experimental and is not yet deployed to the upstream package


The X.org driver for Raspberry Pi can be installed with the xf86-video-fbdev or xf86-video-fbturbo-git package.


Memory split between the CPU and GPU can be set in boot/config.txt by adjusting the parameter gpu_mem which stands for the amount of RAM in MB that is available to the GPU (minimum 16, default 64) and the rest is available to the ARM CPU.

HDMI/Analogue TV-Out

With the default configuration, the Raspberry Pi uses HDMI video if a HDMI monitor is connected. Otherwise, it uses analog TV-Out (also known as composite output or RCA) To turn the HDMI or analog TV-Out on or off, have a look at /opt/vc/bin/tvservice

Use the -s parameter to check the status; the -o parameter to turn the display off and -p parameter to power on HDMI with preferred settings.

Adjustments are likely required to correct proper overscan/underscan and are easily achieved in /boot/config.txt in which many tweaks are set. To fix, simply uncomment the corresponding lines and setup per the commented instructions:

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border

Or simply disable overscan if the TV/monitor has a "fit to screen" option.


Users wishing to use the analog video out should consult this config file which contains options for non-NTSC outputs.


The commands for the camera module are included as part of the raspberrypi-firmware package: $ /opt/vc/bin/raspistill $ /opt/vc/bin/raspivid

Append to /boot/config.txt: gpu_mem=128 start_file=start_x.elf fixup_file=fixup_x.dat Optionally


The following is a common error:

mmal: mmal_vc_component_enable: failed to enable component: ENOSPC
mmal: camera component couldn't be enabled
mmal: main: Failed to create camera component
mmal: Failed to run camera app. Please check for firmware updates

which can be corrected by setting these values in /boot/config.txt: cma_lwm= cma_hwm= cma_offline_start=

Another common error: mmal: mmal_vc_component_create: failed to create component 'vc.ril.camera' (1:ENOMEM) mmal: mmal_component_create_core: could not create component 'vc.ril.camera' (1) mmal: Failed to create camera component mmal: main: Failed to create camera component mmal: Only 64M of gpu_mem is configured. Try running "sudo raspi-config" and ensure that "memory_split" has a value of 128 or greater

can be corrected by adding the following line to /etc/modprobe.d/blacklist.conf:

blacklist i2c_bcm2708

In order to use standard applications (those that look for /dev/video0) the V4L2 driver must be loaded. This can be done automatically at boot by creating an autoload file, /etc/modules-load.d/rpi-camera.conf:


The V4L2 driver by default only allows video recording up to 1280x720, else it glues together consecutive still screens resulting in videos of 4 fps or lower. Adding the following options removes this limitation, /etc/modprobe.d/rpi-camera.conf:

options bcm2835-v4l2 max_video_width=3240 max_video_height=2464

Onboard Hardware Sensors


Temperatures sensors can be queried with utils in the raspberrypi-firmware package.

$ /opt/vc/bin/vcgencmd measure_temp


Four different voltages can be monitored via /opt/vc/bin/vcgencmd:

$ /opt/vc/bin/vcgencmd measure_volts <id>

Where <id> is:

  • core for core voltage
  • sdram_c for sdram Core voltage
  • sdram_i for sdram I/O voltage
  • sdram_p for sdram PHY voltage


BCM2708 has a hardware watchdog which can be utilized by enabling the bcm2708_wdog kernel module.

For proper operation the watchdog daemon also has to be installed, configured (by uncommenting the "watchdog-device" line in /etc/watchdog.conf) and enabled.

This should also apply for Raspberry Pi 2 by using the bcm2709_wdog module and Raspberry Pi 3 by using the bcm2835_wdt module.

Hardware Random Number Generator

Arch Linux ARM for the Raspberry Pi had the bcm2708-rng module set to load at boot; starting with kernel 4.4.7 the bcm2835_rng module replaces the former on Raspberry Pi 2 and Raspberry Pi 3 units.

Install rng-tools and tell the Hardware RNG Entropy Gatherer Daemon (rngd) where to find the hardware random number generator. This can be done by editing /etc/conf.d/rngd:

RNGD_OPTS="-o /dev/random -r /dev/hwrng" 

and enabling and starting the rngd service.

If haveged is running, it should be stopped and disabled, as it might compete with rngd and is only preferred when there is no hardware random number generator available.

Once completed, this change ensures that data from the hardware random number generator is fed into the kernel's entropy pool at /dev/random. To check the available entropy, run:

# cat /proc/sys/kernel/random/entropy_avail 

The number it reports should be around 3000, whereas before setting up rngd it would have been closer to 1000.

I/O Pins


To be able to use the GPIO pins from Python, use the RPi.GPIO library. Install the python-raspberry-gpio package from the AUR.


To enable the /dev/spidev* devices, uncomment the following line in /boot/config.txt:



Install i2c-tools and lm_sensors packages.

Configure the bootloader to enable the i2c hardware by appending to /boot/config.txt:


Configure the i2c-dev and i2c-bcm2708 (if not blacklisted for the camera) modules to be loaded at boot in /etc/modules-load.d/raspberrypi.conf:

i2c-dev i2c-bcm2708

Reboot the Raspberry Pi and issue the following command to get the hardware address:

i2cdetect -y 0

Note: When using the I2C1 port instead of I2C0, one will need to run i2cdetect -y 1 instead and replace i2c-0 with i2c-1 in the following steps.

Now instantiate the device. Change the hardware address to the address found in the previous step with '0x' as prefix (e.g. 0x48) and choose a device name:

echo <devicename> <hardware address> >/sys/class/i2c-adapter/i2c-0/new_device

Check dmesg for a new entry:

i2c-0: new_device: Instantiated device ds1621 at 0x48

Finally, read the sensor output: sensors


To enable the 1-wire interface add this line to /boot/config.txt and reboot. dtoverlay=w1-gpio

Non-Root GPIO

To use the GPIO/SPI pins as a regular non-root user (in group tty), add the following lines to a new file /usr/lib/udev/rules.d/99-spi-permissions.rules

KERNEL=="spidev*", GROUP="tty", MODE="0660"
SUBSYSTEM=="gpio*", PROGRAM="/bin/sh -c 'chown -R root:tty /sys/class/gpio && chmod -R 775 /sys/class/gpio; chown -R root:tty /sys/devices/virtual/gpio && chmod -R 775 /sys/devices/virtual/gpio; chown -R root:tty /sys/devices/platform/soc/*.gpio/gpio && chmod -R 775 /sys/devices/platform/soc/*.gpio/gpio'"
SUBSYSTEM=="gpio", KERNEL=="gpiochip*", ACTION=="add", PROGRAM="/bin/sh -c 'chown root:tty /sys/class/gpio/export /sys/class/gpio/unexport ; chmod 220 /sys/class/gpio/export /sys/class/gpio/unexport'"
SUBSYSTEM=="gpio", KERNEL=="gpio*", ACTION=="add", PROGRAM="/bin/sh -c 'chown root:tty /sys%p/active_low /sys%p/direction /sys%p/edge /sys%p/value ; chmod 660 /sys%p/active_low /sys%p/direction /sys%p/edge /sys%p/value'"

See Also

Copyright ©2009-2022 Arch Linux ARM
The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a world-wide basis.
The Arch Linux™ name and logo are used under permission of the Arch Linux Project Lead.